Abstract:Flow softening behavior, microstructure evolution and hot working parameters of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy were systematically studied by isothermal hot compression. Based on the analysis of processing maps and the corresponding microstructure, power dissipation efficiency peak occurred at two domains, which were associated with dynamic recrystallization (DRX) and super-plasticity. Pile-up of high density dislocation and a large number of twins were the primary deformation mechanisms at low temperature and high strain rate. As the temperature increases, fine DRX grains promote the movement and rotation of grain boundary, the softening of β phase and the transformation of β→α/α2+γ above 1200 °C improve the deformation capacity of the alloy significantly. Crack-free TiAl sheets were successfully obtained by direct hot rolling process at 1080 °C and 1220 °C. The corresponding microstructure and mechanical properties were analyzed. The sheets rolled at 1080 °C was characterized by near γ (NG)+β0 microstructure with a streamline along the rolling direction, while duplex (DP)+β0 microstructure appeared to be the main microstructure at rolling temperature of 1220 °C. The as-rolled sheet exhibits excellent mechanical properties at 800 °C. The sheet rolled at 1080 °C exhibits 320 MPa yield strength and 468 MPa ultimate tensile strength with 142% elongation. The yield strength, ultimate tensile strength, and elongation of the as-rolled sheet are 446 MPa, 586 MPa, and 3.0%, respectively, when rolled at 1220 °C. The excellent ductility of the sample rolled at 1080 °C is attributed to formation of fine DRX grains due to consumption of twins and substructure under tensile stress, which promote grain boundary slip. Lamellar colonies with fine interlamellar spacing and α2 laths formed at 1220 °C can effectively prevent dislocation motion, resulting in a significant increase in the strength of the alloy.

Microstructures and Mechanical Properties of a Commercial Pure Zirconium during Rolling and Annealing at Different Temperatures

Effect of cold rolling on microstructure and mechanical properties of pure Zr

Evolution of Shear Bands in the Structure of a Zirconium-Based Amorphous Alloy during Rolling at Different Temperatures

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Effect of Zr on microstructure evolution of Ti-Mo composite microalloyed steel during rolling

Microstructure and properties evolution of Mg–2Y–0.6Nd–0.6Zr alloy rolled at room and liquid nitrogen temperature

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Microstructure evolution and recrystallization of Ti6246 alloy in hot‐rolling and annealing processes

Mechanical properties and thermal stability of gradient structured Zr via cyclic skin-pass cryorolling

Effect of Microstructure on Stretch Property for Zr-Sn-Nb New Zirconium Alloys

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Homogenization and Growth Behavior of Second-Phase Particles in a Deformed Zr–Sn–Nb–Fe–Cu–Si–O Alloy

Deformation-strengthening During Rolling Cu60Zr20Ti20 Bulk Metallic Glass

Microstructural evolution and mechanical properties of pure zinc subjected to extrusion and caliber rolling

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Rolling parameters, microstructure control, and mechanical properties of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy: The impact of rolling temperatures

Static globularization and grain morphology evolution of α and β phases during annealing of hot-rolled TC21 titanium alloy