Abstract:Flow softening behavior, microstructure evolution and hot working parameters of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy were systematically studied by isothermal hot compression. Based on the analysis of processing maps and the corresponding microstructure, power dissipation efficiency peak occurred at two domains, which were associated with dynamic recrystallization (DRX) and super-plasticity. Pile-up of high density dislocation and a large number of twins were the primary deformation mechanisms at low temperature and high strain rate. As the temperature increases, fine DRX grains promote the movement and rotation of grain boundary, the softening of β phase and the transformation of β→α/α2+γ above 1200 °C improve the deformation capacity of the alloy significantly. Crack-free TiAl sheets were successfully obtained by direct hot rolling process at 1080 °C and 1220 °C. The corresponding microstructure and mechanical properties were analyzed. The sheets rolled at 1080 °C was characterized by near γ (NG)+β0 microstructure with a streamline along the rolling direction, while duplex (DP)+β0 microstructure appeared to be the main microstructure at rolling temperature of 1220 °C. The as-rolled sheet exhibits excellent mechanical properties at 800 °C. The sheet rolled at 1080 °C exhibits 320 MPa yield strength and 468 MPa ultimate tensile strength with 142% elongation. The yield strength, ultimate tensile strength, and elongation of the as-rolled sheet are 446 MPa, 586 MPa, and 3.0%, respectively, when rolled at 1220 °C. The excellent ductility of the sample rolled at 1080 °C is attributed to formation of fine DRX grains due to consumption of twins and substructure under tensile stress, which promote grain boundary slip. Lamellar colonies with fine interlamellar spacing and α2 laths formed at 1220 °C can effectively prevent dislocation motion, resulting in a significant increase in the strength of the alloy.

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Microstructure evolution and mechanical properties of Al−3.6Cu−1Li alloy via cryorolling and aging

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Microstructure evolution, mechanical response, and corrosion resistance for a 2195 Al-Li alloy under different rolling reductions during cryorolling

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy

Study of mechanical characteristics and strengthening mechanism of AA5154 during cryogenic rolling

Deformation mechanism and mechanical properties of a CoCrFeNi high-entropy alloy via room-temperature rolling, cryorolling, and asymmetric cryorolling

Effect of Pretreatment and Cryogenic Temperatures on Mechanical Properties and Microstructure of Al-Cu-Li Alloy

Mechanical Properties and Microstructure of a Ti-6Al-4V Alloy Subjected to Cold Rolling, Asymmetric Rolling and Asymmetric Cryorolling

Influence of alloy chemistry on the deformation behaviour and anisotropic properties of aluminium ultra-fine-grained thin sheets

The mechanical properties of OFHC copper and CuCrZr alloys after asymmetric rolling at ambient and cryogenic temperatures

Influence of substructures on precipitation behavior and mechanical properties of cryogenic rolled Al-Mg-Si alloys during aging treatment

Mechanical properties of rolled and aged AA6061 sheets at room-temperature and cryogenic environments

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Achieving ultrahigh strength in binary Al-10Mg alloy through heavy cryogenic rolling

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Rolling parameters, microstructure control, and mechanical properties of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy: The impact of rolling temperatures

Cooperative Effect of Grain Size and Cryogenic Temperature on Deformation Behavior and Mechanism of Commercial Pure Al Sheets