Abstract:The enhancement of cryogenic plasticity for some aluminum alloys has attracted broad attention, which provides a new approach to the formability improvement of high-strength aluminum alloys. However, the hardening behavior and the ductility of aluminum alloys at cryogenic temperatures are very sensitive to the microstructure tempered at different conditions, with complex combination of GP zones, second phase precipitates, coarse and equilibrium phases. In this paper, three groups of tempered AA7075 aluminum alloy sheets are elaborately designed by means of different approaches, i.e., solution-treated (W), peak artificial aged (T6), and fast re-dissolved (FD) from T6, to investigate their cryogenic deformation behavior and failure mechanism. The effect on cryogenic plasticity of second phases, including the coarse particles in the matrix and the precipitate free zones (PFZs) accompanied by chain distributed particles along grain boundary, can be isolated by comparison among these three kinds of AA7075 alloys. The cryogenic mechanical properties of AA7075 sheets are evaluated by uniaxial tensile test, and the microstructure evolution observed by transmission electron microscope (TEM), scanning electron microscope (SEM) and laser confocal microscope (LCM). It shows that the enhancement of both ductility and continuous work hardening for W- and FD-tempered AA7075 sheets at cryogenic temperatures results from the uniformly distributed dislocations in the matrix of supersaturated solid solution (SSSS). The relatively low cryogenic ductility of AA7075-FD in comparison with AA7075-W results from the cracked η phases in the interior of grain, which has an increasing brittleness and high stresses on the particle due to the bypassing process at cryogenic condition. Furthermore, the undesirable early fracture of AA7075-T6 alloy during cryogenic deformation process is systematically illustrated from the aspect of interaction between dislocation and second-phase particles. Beside the cracked η phases in the interior of grains, defects also appear in the non-coherent interface between PFZ and the equilibrium η phase due to stain localization at grain boundary. As a result, AA7075-T6 alloy exhibits a ductile-brittle mixed fracture mode dominated by PFZ and the equilibrium η phase at grain boundary.

Mechanical properties of rolled and aged AA6061 sheets at room-temperature and cryogenic environments

Edge-crack free and high mechanical properties of AA7075 sheets by using cryorolling and subsequent aging

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Effect of Cryorolling and Aging Treatment on Erichsen Formability of AA7075 Sheets at Room and Cryogenic Temperatures

Effects of cryorolling, room temperature rolling and aging treatment on mechanical and corrosion properties of 7050 aluminum alloy

High-Temperature Tensile Mechanical Properties and Microstructure of Rolled 6082-T6 Aluminum Alloy Sheets

Microstructure evolution and mechanical properties of Al−3.6Cu−1Li alloy via cryorolling and aging

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Mechanical Properties of Rolled Copper Foils in Cryogenic and Room‐Temperature Environments

Mechanical properties and microscopic mechanisms of 2219-T6 aluminum alloy under dynamic tension with cryogenic temperatures

Cryogenic Deformation Behaviour of Aluminium Alloy 6061-T6

Effects of annealing treatment on mechanical properties of 8011 aluminum alloy after cryogenic rolling

Effect of Different Cryogenic Rolling Strains on the Impact Properties of 6082 Aluminum Alloy

Study of mechanical characteristics and strengthening mechanism of AA5154 during cryogenic rolling

Microstructure evolution, mechanical response, and corrosion resistance for a 2195 Al-Li alloy under different rolling reductions during cryorolling

Mechanical Properties and Microstructure of a Ti-6Al-4V Alloy Subjected to Cold Rolling, Asymmetric Rolling and Asymmetric Cryorolling

Tensile properties and a modified s-Johnson-Cook model for constitutive relationship of AA7075 sheets at cryogenic temperatures

Influence of Rolling Temperature on Microstructure and Tensile Properties of AZ31 Sheets

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Microstructure and mechanical properties of AA1050/AA6061 multilayer composites via accumulative roll bonding and cryorolling and subsequent aging

Cryogenic Deformation Behavior and Failure Mechanism of AA7075 Alloy Sheets Tempered at Different Conditions