Abstract:Cryogenic treatment has high potential for improving the deformation behavior through the recrystallization at a low temperature. In this work, true stress-strain curves were obtained via compression tests to understand the deformation behavior of an AA7075 under cryogenic conditions. Results showed a significant improvement in the flow stress of AA7075, increasing from 260 to 560 MPa at the yield point. The strain hardening exponent (n) also increased from 0.25 to 0.35 after deformation at cryogenic temperatures. The presence of Al2CuMg phase influenced the deformation texture of the tested aluminum alloy, resulting in more elongated grains and fine sub-grains after deformation at cryogenic temperatures, due to the hindered recrystallization. Microstructure evolution after deformation at room and cryogenic temperatures was investigated using EBSD technique to characterize texture and recrystallized grains. The results indicated that the spacing of the high-angle grain boundaries (HAGBs) in the sample deformed at room temperature was slightly larger than in the cryogenically treated sample. The alloy deformed at the cryogenic temperature exhibited a higher strain hardening exponent (n = 0.35) compared to room temperature deformation (n = 0.25). Furthermore, finite element analysis supported the experimental findings, showing that the Plastic Equivalent Strain (PEEQ) of the model tested at cryogenic temperature was higher than at room temperature, attributed to grain refinement during low-temperature deformation. The calculated effective stress responses at cryogenic temperatures for the investigated flow stress aligned well with the experimental results. These new aspects and mechanisms of deformation of aluminum alloys at cryogenic temperatures can improve the formability of high-strength alloys in the future production of more complex and integrated lightweight components.

Influence of alloy chemistry on the deformation behaviour and anisotropic properties of aluminium ultra-fine-grained thin sheets

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Study of mechanical characteristics and strengthening mechanism of AA5154 during cryogenic rolling

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Effect of Different Cryogenic Rolling Strains on the Impact Properties of 6082 Aluminum Alloy

INFLUENCE OF A LOW-TEMPERATURE PLASTIC-DEFORMATION PROCESS ON THE MICROSTRUCTURE OF AN Al-Si-Mg ALUMINUM ALLOY

Fatigue Behavior of Ultrafine-Grained 5052 Al Alloy Processed Through Different Rolling Methods

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Microstructure evolution and mechanical properties of Al−3.6Cu−1Li alloy via cryorolling and aging

Effects of annealing treatment on mechanical properties of 8011 aluminum alloy after cryogenic rolling

Effects of cryorolling, room temperature rolling and aging treatment on mechanical and corrosion properties of 7050 aluminum alloy

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Effect of Cryorolling and Ageing on the Microstructure and Mechanical Properties of Al 7085 Alloy

Edge-crack free and high mechanical properties of AA7075 sheets by using cryorolling and subsequent aging

The improvement of deformability in AA7075 alloy through cryogenic treatment and its correlation with microstructural evolution and FE modelling

The Effect of Cold Rolling on the Corrosion Behaviour of 5083 Aluminium Alloys

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy