Abstract:In the present investigation, equiatomic CoCrFeMnNi high entropy alloy (HEA) was subjected to 80% cold rolling (as-rolled) followed by isothermal annealing treatment at 700 °C for different time periods. Microstructural characterization was performed using electron back-scattered diffraction (EBSD) and electron channeling contrast imaging (ECCI) techniques on the as-rolled and annealed samples. The as-rolled microstructure consisted of elongated grains mainly composed of strong α-fiber and weak γ-fiber textures. The as-rolled sample showed the formation of ingrain SBs in the γ-fiber grains, which served as preferential sites for grain nucleation. The annealing treatment of as-rolled samples at 700 °C cause static recovery (SRV) before 5 minutes of heat-treatment, whereas static recrystallization (SRX) was observed after 5 minutes of heat-treatment in the CoCrFeMnNi alloy samples. A faster rate of recrystallization kinetics was observed after 15 minutes of heat-treatment. The annealing treatment reduced the intensity of α-fiber and enhanced the Copper, Cube and P ({011} ) texture components. Copper components originated from coarse recrystallized grains, which were the results of localized grain growth phenomena. Unusual behavior of banded featured α-fiber grains was observed during the annealing process. These banded grains in the partially annealed samples consisted of subgrain-boundaries and showed a delayed response to recrystallization as compared to grains with other orientations. Stored energy (SE) and Taylor factor (M) calculations were also used to understand the delayed recrystallization response of the banded featured/retained deformed grains. The microhardness value of the as-rolled sample was approximately 450 Hv, which decreased to around 230 Hv for the fully recrystallized grains.

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Influence of alloy chemistry on the deformation behaviour and anisotropic properties of aluminium ultra-fine-grained thin sheets

On the Relationship between Thermomechanical Processing Parameters and Recrystallization Texture in AA1100 Aluminum Alloy

Evolution of Microstructure and Texture During Recovery and Recrystallization in Heavily Rolled Aluminum

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Recrystallization and Texture Evolution of Cold-Rolled AZ31 Mg Alloy Treated by Rapid Thermal Annealing

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Influence of substructures on precipitation behavior and mechanical properties of cryogenic rolled Al-Mg-Si alloys during aging treatment

Effects of annealing treatment on mechanical properties of 8011 aluminum alloy after cryogenic rolling

Microstructure evolution and mechanical properties of Al−3.6Cu−1Li alloy via cryorolling and aging

Revealing the inhomogeneous nature of microstructure and texture evolution in the cold-rolled CoCrFeMnNi alloy during static recrystallization

Microstructure and Texture of Heavily Cold-Rolled and Annealed Fcc Equiatomic Medium to High Entropy Alloys

In-situ observations of static recrystallization and texture formation in a cold-rolled CoCrFeMnNi high entropy alloy

Microstructure evolution, mechanical response, and corrosion resistance for a 2195 Al-Li alloy under different rolling reductions during cryorolling

Recovery and Recrystallization in Commercial Purity Aluminum Cold Rolled to an Ultrahigh Strain

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

Microstructure and Texture Evolution of Cold Rolled 1070 Al Alloy During the Subsequent Annealing Treatment