Abstract:In this contribution, the underlying mechanisms of microstructure evolution and texture development during the cold rolling and annealing of a Ti-2Al-1.5Mn alloy were investigated and elucidated comprehensively. As a result of the heightened dislocation density and grain boundary, the hardness ascended as the successive reductions applied. However, the annealing treatment reinstated the structure through complete recrystallization. During cold working, the dominant basal and prismatic glide inclined the c-axis and < 101̅0 > axis towards the compressive direction and the rolling direction (RD), respectively. The primary rolled orientation consisted of < 101̅0 > fiber, the orientation of { 1̅21̅3 }< 101̅0 > with Euler angle {10°, 45°, 0°}and { 1̅21̅7 }< 101̅0 > with Euler angle {5°, 25°, 0 °} were predominant. Schmid Factor (SF) analysis and orientation rotation related to various textures demonstrated that basal slipping resulted in a descending φ angle in the Bunge system and < 101̅0 > pole parallel to the RD was the stable orientation. It was revealed that the recrystallized grains preponderantly exhibited textures inherited from the rolled matrix, but a new T-type texture also emerged. This implies that both the strain-induced boundary migration (SIBM) mechanism and selective grain growth, which nucleates at different sites, manipulate the annealing process. The study enhances our comprehension of texture evolution mechanisms involved in the plastic forming and helps ascertain the most effective operational parameters for producing high-performance titanium plates.

Recrystallization and Texture Evolution of Cold-Rolled AZ31 Mg Alloy Treated by Rapid Thermal Annealing

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Annealing Behavior Of Rolled Az31 Alloy Sheet

Microstructure and texture evolution of cold-rolled Mg-3Al-1Zn alloy by electropulse treatment stimulating recrystallization

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

Recrystallization and Anisotropy of AZ31 Magnesium Alloy by Asynchronous Rolling

Multiple-twinning induced recrystallization and texture optimization in a differential-temperature-rolled AZ31B magnesium alloy with excellent ductility

Texture Evolution in Cold-Rolled AZ31 Magnesium Alloy During Electropulsing Treatment

Evaluation of static recrystallization and grain growth kinetics of hot-rolled AZ31 alloy

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

On the Relationship between Thermomechanical Processing Parameters and Recrystallization Texture in AA1100 Aluminum Alloy

Microstructure and properties of AZ31 alloy by static recrystallisation at lower temperature

Effects of cryogenic treatment on microstructure and mechanical properties of AZ31 magnesium alloy rolled at different paths

Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling

Effect of Final Rolling Temperature on Microstructures and Mechanical Properties of AZ31 Alloy Sheets Prepared by Equal Channel Angular Rolling and Continuous Bending

Grain refining and improving mechanical properties of AZ31 Mg alloy sheets by multi-pass warm rolling with falling temperature

Recrystallization and Precipitation of Β-Mg17al12 Phase of the Cold-Rolled Mg-9Al-1Zn Alloy Strip During Isothermal Annealing