Abstract:The recrystallization process in 1565 ch aluminium alloy samples was studied in this paper. Existing and well-studied AA5182 aluminium alloy was also investigated for comparison. Samples of both alloys were cut from pre-homogenized ingots and rolled in different modes. After rolling the samples were annealed at different temperatures and the resulting microstructure was studied using scanning electron microscopy and optical microscopy, as well as EBSD (Electron backscatter diffraction) analysis. The study revealed significant differences in the recrystallization processes of these two alloys. Signs of the recrystallization onset without grain growth process can be observed at 10% deformation in 1565 ch alloy. At the same time signs of recrystallization in AA5182 can been observed only when the degree of deformation is over 30%, but the process itself is much faster. 5182 alloy fully recrystallizes after all hot rolling schedules, except for those with 10% deformation. In such case recrystallization timing as a function of Zener-Hollomon parameter and prior strain level ranges from a few seconds to half an hour. In major cases 1565 ch alloy has partially recrystallized structure, which takes 10 to 95 volume %. Exception is the schedule with deformation 50% and Zener parameter 1.77 × 1015, where full recrystallization occurs. With such strain parameters 1565 alloy grain size reaches 6–14 μm. At the same time similar processing provides larger grain size in 5182 alloy, it reaches 10–20 μm. Substructure review immediately after deformation demonstrated, that cellular polygonised structure forms faster in 1565 ch alloy, which can be explained by higher magnesium content. In both cases PSN nucleation mechanism prevails. However, other grain nucleation mechanisms can be observed in 5182 alloy. The main reasons for the abovementioned phenomenon are different magnesium contents and volumes of fine secondary phases.

Evolution of Microstructure and Texture During Recovery and Recrystallization in Heavily Rolled Aluminum

Recovery and Recrystallization in Commercial Purity Aluminum Cold Rolled to an Ultrahigh Strain

Nanostructured Aluminium - Recovery And Recrystallization

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Microstructure and Texture Evolutions of Aa1050 Aluminum Alloy Cold Rolled to High Strains

Recovery and Recrystallization as a Function of Deformed Microstructure Orientation in Coarse Grained Cold-Rolled Ni

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Thermal Stability of Aluminum Cold Rolled to Large Strain

On the Relationship between Thermomechanical Processing Parameters and Recrystallization Texture in AA1100 Aluminum Alloy

Revealing the inhomogeneous nature of microstructure and texture evolution in the cold-rolled CoCrFeMnNi alloy during static recrystallization

Microstructural Parameter-Based Characterization of Annealing Behaviour in Metals Deformed to High Strains

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

Influence of Residual Stress around Constituent Particles on Recrystallization and Grain Growth in Al-Mn-Based Alloy during Annealing

Evolution of Microstructure and Crystallographic Texture in Severely Cold Rolled High Entropy Equiatomic CoCrFeMnNi Alloy During Annealing

Microstructure and Texture Evolution of Cold Rolled 1070 Al Alloy During the Subsequent Annealing Treatment

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

In-situ observations of static recrystallization and texture formation in a cold-rolled CoCrFeMnNi high entropy alloy

Specific Features of Microstructural Evolution During Hot Rolling of the As-Cast Magnesium-Rich Aluminum Alloys with Added Transition Metal Elements

Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation

RELEVANCE OF COLD-ROLLING TECHNOLOGY FOR THE TEXTURE AND ANISOTROPY OF EN AW-8011A ALUMINUM ALLOYS

Study of the recrystallization behaviour of the aluminium 1565ch alloy during hot rolling of the as cast structures