Abstract:When using well-designed multiple-stage heavy-drawn processes, i.e., cold rolling, drawing and cluster drawing to fabricate a metallic wire or fiber in steps, cold rolling and annealing are critical steps due to their effect on the initial microstructure before the heavy-drawn process. Understanding the relationship between microstructure evolution and cold rolling followed by annealing is required for smoothly implementing the heavy-drawn process. In this work, the evolution behavior in terms of the microstructure during cold rolling followed by annealing was investigated in a novel C-2000 alloy that is a promising candidate material for the fabrication of high-performance metallicwire. The investigation encompassed parameters including the grain size, grain boundaries, recrystallization texture, and short-range ordered (SRO) structure. Results show that the grain size distribution of the cold-rolledC-2000 alloy followed by annealing at 900 °C is quite uneven. The low-angle grain boundaries induced by cold rolling are more frequently transformed into the Σ3 twin boundaries during recrystallization. At the initial stage of annealing at 900 °C after cold rolling, the contents of different texture components are significantly different, but the differences tend to decrease with the extension of the annealing time. In addition, cold rolling destroys SRO domains formed during solid solution water quenching, and the destruction of SRO affects the precipitation of the long-range ordered phase during annealing. Incoherent Σ3ic with curved grain boundaries play an important role in the recrystallization of nucleation sites in the process of static recrystallization by nucleation–growth.

RELEVANCE OF COLD-ROLLING TECHNOLOGY FOR THE TEXTURE AND ANISOTROPY OF EN AW-8011A ALUMINUM ALLOYS

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Influence of alloy chemistry on the deformation behaviour and anisotropic properties of aluminium ultra-fine-grained thin sheets

Evolution of Microstructure and Texture During Recovery and Recrystallization in Heavily Rolled Aluminum

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

The Influence of Annealing on the Microstructural and Textural Evolution of Cold-Rolled Er Metal

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

Textures of Non-Oriented Electrical Steel Sheets Produced by Skew Cold Rolling and Annealing

Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Microstructure, Texture, and Anisotropic Properties of High-Strength Low-Alloy Steel

Microstructure and Texture Evolution of Cold Rolled 1070 Al Alloy During the Subsequent Annealing Treatment

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

On the Relationship between Thermomechanical Processing Parameters and Recrystallization Texture in AA1100 Aluminum Alloy

Interpretation of the strain state during cross-roll rolling of aluminum by means of texture analysis

The Effects of Cold Rolling and Annealing on the Microstructure Evolution of Ordered C-2000 Alloy during Metallic Wire Preparation

Effects of annealing treatment on mechanical properties of 8011 aluminum alloy after cryogenic rolling

Microstructure and Texture Evolutions of Aa1050 Aluminum Alloy Cold Rolled to High Strains

Effect of cross cold rolling and annealing on microstructure and texture in pure nickel

The Dependence of Final Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si–Cu Alloy Sheets on the Intermediate Annealing