Abstract:In the present work, the objectives were to investigate the type of microstructure and texture that developed after two step cold rolling — continuous annealing. Further, an attempt has been made to correlate the microstructure and texture with mechanical properties. Interstitial free (IF) and interstitial free — high strength (IF-HS) steel sheets which contain almost γ-fiber textures, were subjected to two step cold rolling for different percentage of reduction and further continuously annealed. It was observed that cold rolling strengthened the region of (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations of α-fiber as well as γ-fiber. After continuous annealing, cold rolled γ-fiber as well as (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations transformed to extremely strong new γ-fiber. It was found that at two steps 80% cold rolling -continuous annealing, drawability of IF steel sheet was exceptionally high i.e. around 3.15, whereas for IF-HS steel sheets, it was around 2.7. Although, two steps cold rolling -continuous annealing enhanced percentage elongation and stretchability exceptionally, but it reduced the yield strength substantially. However, ultimate tensile strength was hardly affected. In addition, it is also observed that two steps cold rolling — continuous annealing developed uniform grain size in both the grades of steel sheets.

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Formation of recrystallization texture and its effect on deep drawability for high-purified ferritic stainless steel by two step cold rolling

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Effect of cold rolling reduction on microstructure, mechanical properties, and texture of deep drawing dual-phase (DP) steel

Evolution of Through-Thickness Texture in Ultra Purified 17%cr Ferritic Stainless Steels

Understanding the Mechanisms of Texture Evolution of a Fe-24Cr-22Ni-7Mo Super Austenitic Stainless Steel During cold Rolling and Annealing

Effect of the size and dispersion of precipitates formed in hot rolling on recrystallization texture in ferritic stainless steels

Effects of Reduction Partitioning in Two-Stage Cold Rolling on the Surface Ridging Resistance of Ferritic Stainless Steel

Texture and microstructure evolution during cold rolling of a strip cast and of a hot rolled austenitic stainless steel

Effect of two step cold rolling — continuous annealing on micro-structures, textures and mechanical properties in IF and IF-HS steel sheets

An Investigation of Friction Coefficient on Microstructure and Texture Evolution of Interstitial-Free Steel during Warm Rolling and Subsequent Annealing

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

EFFECT OF COLD ROLLING PROCESS ON TEXTURE EVOLUTION OF GRADIENT MICROSTRUCTURE IN Fe-3,0 % Si NON-ORIENTED SILICON STEEL

Crystal Plasticity-Based Assessment of Constitutive Laws for Microstructure and Rolling Texture Capture in Ferritic Stainless Steel During Cold Rolling

Correlation between formability, ridging and recrystallization texture development in ferritic stainless steel fabricated by introducing intermediate annealing during cold rolling

Effects of microstructure and texture on the deep drawability of C10200 copper sheets

Effects of Two-Stage Cold Rolling Schedule on Microstructure and Texture Evolution of Strip Casting Grain-Oriented Silicon Steel with Extra-Low Carbon

Dislocation Strengthening and Texture Evolution of Non-Oriented Fe-3.3 wt% Si Steel in Double Cold Rolling

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel