Abstract:The effect of finish rolling temperature on the austenite-(γ) to-bainite (α) phase transformation is quantitatively investigated in high-strength C-Mn steels using an alternative crystallographic γ reconstruction procedure, which can be directly applied to experimental electron backscatter diffraction mappings. In particular, the current study aims to clarify the respective contributions of the γ conditioning during the hot rolling and the variant selection during the phase transformation to the inherited texture. The results confirm that the sample finish rolled at the lowest temperature [1102 K (829 °C)] exhibits the sharpest transformation texture. It is shown that this sharp texture is exclusively due to a strong variant selection from parent brass {110}11¯2\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \left\langle {1\bar{1}2} \right\rangle $$\end{document}, S {213}3¯6¯4\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \left\langle {\bar{3}\bar{6}4} \right\rangle $$\end{document} and Goss {110}〈001〉 grains, whereas the variant selection from the copper {112}1¯1¯1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \left\langle {\bar{1}\bar{1}1} \right\rangle $$\end{document} grains is insensitive to the finish rolling temperature. In addition, a statistical variant selection analysis proves that the habit planes of the selected variants do not systematically correspond to the predicted active γ slip planes using the Taylor model. In contrast, a correlation between the Bain group to which the selected variants belong and the finish rolling temperature is clearly revealed, regardless of the parent orientation. These results are discussed in terms of polygranular accommodation mechanisms, especially in view of the observed development in the hot-rolled samples of high-angle grain boundaries with misorientation axes between 〈111〉γ and 〈110〉γ.

Texture and microstructure evolution during cold rolling of a strip cast and of a hot rolled austenitic stainless steel

Understanding the Mechanisms of Texture Evolution of a Fe-24Cr-22Ni-7Mo Super Austenitic Stainless Steel During cold Rolling and Annealing

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Microstructure and texture evolutions of 310S austenitic stainless steel after cryogenic rolling and subsequent annealing: X-ray and electron backscatter diffraction studies

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Microstructures and textures in cold-rolled aluminium strip

Strain-induced martensite formation in cryorolled AISI 317 L stainless steel

Evolution of Through-Thickness Texture in Ultra Purified 17%cr Ferritic Stainless Steels

Formation of recrystallization texture and its effect on deep drawability for high-purified ferritic stainless steel by two step cold rolling

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Microstructure Evolution and Texture Characteristics of Pure Nickel N6 During Cold Rolling Process

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

Crystal Plasticity-Based Assessment of Constitutive Laws for Microstructure and Rolling Texture Capture in Ferritic Stainless Steel During Cold Rolling

Effect of the size and dispersion of precipitates formed in hot rolling on recrystallization texture in ferritic stainless steels

Recrystallization Texture Evolution of Cold-Rolled Cu Foils Governed by Microstructural and Sample Geometrical Factors During Heating

Crystallographic Reconstruction Study of the Effects of Finish Rolling Temperature on the Variant Selection During Bainite Transformation in C-Mn High-Strength Steels

Texture and superelastic behavior of cold-rolled TiNbTaZr alloy

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Effect of cold rolling on microstructure and texture evolution in strip casting Fe-36%Ni invar alloy foil

An Investigation of Friction Coefficient on Microstructure and Texture Evolution of Interstitial-Free Steel during Warm Rolling and Subsequent Annealing

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing