Abstract:In this paper, a high-dense alumina ceramics were prepared through the two-step pressureless sintering process with high-purity alumina powder as raw materials and high-purity MgO as sintering aids. The effects of the sintering temperature in the first-step (T1) and the soaking time (t) in the second sintering step (T2) on the density, microstructure and mechanical properties of the alumina ceramics were studied. The results indicated that the relative density increased with the increase of T1 temperature whereas it increased and then decreased with the increase of MgO content. Higher T1 temperature and extended soaking time caused larger grain size, which accompanied with the Ostwald ripening of the grain and led to non-uniformity of grain size distribution. The addition of MgO was beneficial to the decrease in grain size due to pinning effect of the second phase. For samples with shorter soaking time, sintering with higher T1 temperature led to better mechanical properties because of its high density. However, for the long soaking time, all samples after sintering at different T1 temperature were fully-densified, so the grain size become to the dominant factor of strength, thus samples with lower T1 temperature exhibited better mechanical properties due to the refinement grain. Excessive addition of MgO resulted in defects, by which the strength increased firstly and then decreased slightly with the increased MgO content. For the samples with 2.5wt.% MgO, the optimum condition for the two-step pressureless sintering was T1=1450°C and T2=1400°C for 20h, and the obtained sample achieved the relative density of 96% and the strength of 507±32MPa.

Effect of Synthesizing Temperature of Alumina Powder with Rose-Like Structure on the Microstructure and Mechanical Property of Alumina Ceramic

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Microstructures of Nanosized Alumina Powders Synthesized by Sol-Gel Method

Synthesis and sintering behavior of a nanocrystalline α-alumina powder

Microstructure and Properties of Alumina Ceramics Prepared from Submicrometer Alumina Powder with MgO–ZrO2 Coated on Alumina Grain Surface

Effect of Sintering Temperature on Microstructure and Mechanical Behavior of Alumina-Based Ceramic Shell by SLS

Microstructure and Mechanical Properties of Ceramics Obtained from Chemically Co-Precipitated Al 2 O 3 -Gdalo 3 Nano-Powders with Eutectic Composition

Preparation of alumina ceramic template by the molten salt method

An easy approach to adjust microstructure and physical properties in alumina

Enhancing microstructural properties of alumina ceramics via binary sintering aids

Microstructure, mechanical and thermo-physical properties of hot-pressed Al2O3-GdAlO3-ZrO2 ceramics with eutectic composition

Insights into Intragranular Precipitation and Strengthening Effect in Al2O3/SmAlO3 Ceramic with Eutectic Composition

Synthesis, Densification and Characterization of Nanosized Oxide Ceramic Powders with Eutectic Compositions by Heating of Alcohol-Aqueous Salt Solutions

The Preparation and Properties of Alumina Ceramics Through a Two-Step Pressureless Sintering Process

SINTERING PROCESS OF ALUMINA CERAMICS WIH PLATE-LIKE ALUMINA SEEDS

Fabrication and mechanical properties of layered ceramic based on mullite platelets prepared via molten salt method

Preparation and research of fine-grained alumina with high mechanical properties

Preparation of High Purity Alumina Ceramic Supports at Low Temperature

Microstructural Optimization of Alumina Prepared from Ultrafine Theta-Phase Powder for High Strength Applications