Abstract:s Mullite whiskers were synthesized based on the S-L-S growth mechanism at high temperatures using nano-alumina sol and nano-silica sol as the main materials and ammonium molybdate tetrahydrate as an additive. The effects of the silica-aluminum ratio, addition of ammonium molybdate catalyst, sintering temperature, and sintering time on the generation of mullite whiskers were systematically investigated to determine the optimal synthesis conditions. It was shown that the best raw material formulation was (3Al 2 O 3 ·2.2SiO 2 ) 8 (MoO 3 ) 2 , which minimized the mass loss of precursor powder at 0–1200°C, with only 23.62%. The mullite whiskers generated by sintering for 1–3 h maintained good microforms without agglomeration. The optimal growth conditions were 1300°C sintering for 1 h. The resulting mullite whiskers grew along the [240] direction and had the largest aspect ratios up to 10.2–14.3. The highest generation rate was up to 94.5 wt% with a grain size of 81.6 nm. The BET surface area was 2.308 m 2 /g and the pore size was 5.44 nm. The mass loss at 0–1200°C was the least, only 1.32%, with good thermal stability. In addition, the effects of (xAl 2 O 3 ·ySiO 2 ) 8 (MoO 3 ) 2 (x:y=3:1.8, 3:2, 3:2.2) whiskers treated at 1300°C on the APSB adhesive and MSABS adhesive bonding were investigated in this paper, it was clear that whiskers with x:y=3:2.2 had the best enhancement effect. For APSB adhesive strength could be increased by up to 55% and the fracture displacement by 2.42 times. For MSABS adhesives, the strength could be increased by up to 47% and the fracture displacement by 1.49 times.

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

Impact of the Mineral Composition and Sintering Temperature on the Synthesis of Anorthite Ceramics

Influence of CaO content by mass in sintering aid and sintering temperature on the properties of Al2O3-based microwave ceramic materials

Preparation and properties of porous mullite-based ceramics fabricated by solid state reaction

Effects of micro-powder and firing temperature on microstructure and properties of corundum-mullite materials

Effect Of Sintering Process On Micro-structure And Properties Of Mullite Porous Ceramics Containing magnesium oxide

A Simple and Efficient Way to Prepare Porous Mullite Matrix Ceramics Via Directly Sintering SiO2-Al2O3 Microspheres

Effect of particle size of associated rare earth kaolin powder on the sintering and properties of synthetic mullite

Microstructure evolution and mechanical behavior of a mullite fiber heat‐treated from 1100 to 1300°C

Effect Of Y2o3 On Property Of Mullite Ceramic Enhanced By Andalusite

Physico-Mechanical and Microstructure Characteristics of Porous Mullite Ceramics

Effects of Composite Sintering Additives: Al(OH)3+Y2O3+CaF2 on the Performance of Porous Mullite Oxide-Bonded SiC Ceramics

Effects of sintering temperature on properties of porous mullite/corundum ceramics

Effect of Alumina Addition on the Properties of Corundum-Mullite Ceramic Matrix

Properties of Mullite Sol Bonded with High Aluminum Refractories

Reaction mechanisms and properties of in situ porous Al2O3-ZrO2-mullite composites

Preparation of mullite ceramics with equiaxial grains from powders synthesized by the sol-gel method

The effect of multiple factors on the synthesis of mullite whiskers based on the S-L-S mechanism and the comparison of strengthening performance

Synthesis of mullite from wasted silica brick, wasted fireclay brick and wasted slide gate

Low sintering shrinkage and high strength of porous mullite–zirconia ceramics: Effect of AlF3 and ZrSi2 contents

Sintering Process of Mullite- Corundum Insulation Material with Nano Crystals