Study of the Reason and Measure on One 300MW Reheat Pipe Weld Bead's Blasting & Leaking

Yang Xu

2000-01-01

Abstract:This paper analysises the weld bead's problem that was found during boiler inspection on one 300MW reheat pipes imported from Russia. The paper presents appropiate measure and discusses the metallographic examination. Tables 2

What problem does this paper attempt to address?

Cause Analyses of the Weld Seam Cracks of a Prehydrogenating Reactor

卢志明,童水光,方德明,高增梁,朱小平,吴忠

DOI: https://doi.org/10.3969/j.issn.0254-6094.2003.01.012

2003-01-01

Abstract:Many buried cracks were founded out in the circle weld seam on the cylinder of a prehydrogenating reactor with non destructive inspection. In order to find out the crack causes, the chemical compounds and mechanical performance of the base layer (SA387Gr11C12) and the compound layer ( SA240TP321) materials were inspected, the heat treatment and weld process parameters of the reactor were analyzed, the sensitive indexes of the weld cracks of the reactor cylinder material were calculated, it was concluded that the major factors of the weld cracks of the cylinder were because of the lack of the high temperature temper insulation time, the high sensitive index of the weld cracks of the reactor cylinder, the low preheating temperature before welding and the weld complicacy of the intermediate layer of the compound steel sheets. Some heat treatment and weld process parameters were proposed for the reference of the same type apparatuses.
Study on Stress Intensity of Welding Parts of Small Dlameter Tube to Reheater in Coal-burning Thermo-electric Factory with 200 MW Power

LIU Chao-feng,XU Bo-hou,BAO Rong-hao,QI Jun-qing,XU Pei-yuan,LIU Ya-li

DOI: https://doi.org/10.3969/j.issn.1672-4763.2006.02.008

2006-01-01

Abstract:The quality and safety of welding parts of small diameter tube of reheater in thermo-electric factory are vital.If the quality and safety are ignored,frequently halting boiler and making huge economic lost might be after beginning work.Three reasons of leakage of welding parts of reheater were introduced,including incorrect design,bad materials performances and severe conditions.Incorrect design was most important reason.The welding parts of small diameter tube of reheater in a thermo-electric factory were calculated by finite element methods.The finite element analysis model was put forward in this paper.The affection of tilting angle and thickness of welding parts to stress intensity factors were researched in this paper.The figures of stress intensity factors obtained in this paper were referenced by engineer.
Cause and Remedy for Cracks in Weld Seams of Reheater Sealing Plate of Wall Type for 350 MW Power Generating Set Boiler

Zheng Liu

2002-01-01

Abstract:The cause for the cracks in the weld seams of the sealing plate for the reheater of wall type of No.2 boiler at Qitaihe Power Plant was identified through analysis of the mechanism of welding structure, the micrometallographs of welding seams, and the welding prcesses actually used, etc. and necessary corrective actions were suggested as information for future design and on site installation of reheater structures of wall type for similar boilers.
Reason Analysis and Countermeasures for Leakage of Middle-pressure Waste Heat Boiler

Chen Shi-jia

Abstract:This paper examines the chemical components,mechanical properties,metallographie structer for tube sheet and exchange tube of middle-pressure waste heat boiler.The corrosion conditions and its cause are discussed.It found out that the main reason of leakage is that expansion paste and chlorine beyond standars.Feasible measures are taken to stop similar leakage accident.

Environmental Science,Engineering,Materials Science
Analysis of Invalidation Mechanism of Reheater of 1100t/h Boiler

郑准备,张兵,王小迎,梁工英

DOI: https://doi.org/10.3969/j.issn.1001-3814.2004.06.025

2004-01-01

Abstract:The reasons of tube-bursting of the reheaterⅡ of 1100 t/h boiler have been analyzed by means of chemical elements analysis, mechanical performance test, metallographic analysis and electric fracture analysis . The results show that the tube-bursting is caused by short-time overheating and long-time overheating which is coexistent with the running of boiler. Finally, we put forward proposals and preventive measures.
Analysis of Frequent Tube Burst of High Temperature Reheater in 600 MW Unit

Ke Sun,Jia'an Wang,Yu Yan,Jiahao Jiang,Lei Deng,Defu Che

DOI: https://doi.org/10.1109/ispec50848.2020.9351120

2020-01-01

Abstract:The reasons of frequent tube burst of the high temperature reheater in a supercritical 600 MW unit were systematically investigated via the examination of macroscopic inspection, chemical composition, mechanical properties, microstructures, scanning electron microscope and energy disperse spectroscopy detection. It is demonstrated that the tube burst of the high temperature reheater results from not only design factors, but also manufacture quality. Due to the absence of solid solution treatment in spare elbow, the inner dislocations and residual stress increase obviously, which accelerates the precipitation of carbide containing Cr and the formation of Cr depleted zone on grain boundary(GB) subsequently, leading to the decrease of GB corrosion resistance and the final leakage of high temperature reheater tube induced by intergranular corrosion.
Analysis on the cause of crack in connection pipeline of subcritical boiler reheater

Yanfei Zhang,Feng Yun,Wenxuan Fang,Haixue Wang

DOI: https://doi.org/10.1088/1755-1315/508/1/012202

2020-05-01

IOP Conference Series: Earth and Environmental Science

Abstract:Abstract Several coal-fired thermal power boilers with the same sub-critical parameters in Mengxi area of Inner Mongolia have successively suffered from cracking and leakage failure events of reheater connecting pipes, most of which occur at chamfered back tool grooves on the inner wall grooves of pipe welding joints. In order to find out the cause of cracking, typical failure samples were intercepted for macro-morphology, microscopy, SEM, chemical composition, mechanical properties, wall thickness measurement analysis and design and operation data investigation of several boiler equipment. The results show that comprehensive factors such as deviation of burning coal type from design of boiler, automatic dispatching of AGC load in power grid, low nitrogen combustion modification and so on cause changes in boiler combustion conditions and operation, which results in excessive high input level of reheater cooling water, resulting in long-term alternating thermal stress and non-periodic vibration of straight pipe and elbow arranged after fine-tuning of refrigerant flow direction in reheater. Finally, thermal fatigue cracks are induced to initiate and propagate through the stress concentration area of the chamfered knife groove of the inner wall of pipe welded joints.
Cause Analysis and Improvement Measures for Pipeline Cracking of 9Cr-1Mo Material

Liang Xu,FengTao Hu,DongFang Ma,Shuang Hou,ShuHao Zhang

DOI: https://doi.org/10.1088/1742-6596/2276/1/012031

2022-01-01

Journal of Physics Conference Series

Abstract:Abstract The cracking reason of steam drainage pipe in a thermal power plant has been analyzed by means of alloy composition test, microstructure analysis and mechanical calculation. The results show that under the site layout and operation conditions, there were more water accumulated in the pipeline, the temperature of the pipeline decreased, and the movement of the drainage pipe was blocked by the floor, causing the stress of the drainage pipe socket exceeds the allowable value. The type IV creep crack was produced in the fine-grained zone of the heat affected zone of the pipe socket and the leakage failure occurred. The analysis clarifies the cause of cracking of steam drainage pipe and provides reference for avoiding similar cracks in 9Cr-1Mo materials.
Treatment and Analysis on Pipe Explosion of Low-Temperatme Reheater of "W" Flame Boiler

Zhang Xiao-bo,Pan Xiao-wen

DOI: https://doi.org/10.3969/j.issn.1006-348X.2006.04.014

2006-01-01

Abstract:This paper introduces situation,reason analyzing and solved method of two FW 1170.4t/h boiler low-temperature reheater which frequently explosion and effect after retrofit in some power plant.
Analysis of the Vibration Damage Mechanism of the Tube Bundles of a Glycol Re-Boiler

苏文献,桑芝富,陈志平

DOI: https://doi.org/10.3969/j.issn.0254-6094.2001.06.007

2001-01-01

Abstract:Through the analysis of the leak between the tubes and the tube sheet of a vertical fixed tube sheet re boiler,it was found out that the leak cause at the tube inlet of the re boiler was because of the small amplitude vibration induced by the tube bundles under the horizontal action of the shell side,this vibration applied periodic alternative stress on the connection between the tubes and the tube sheet,leading to a fatigue damage at the tube inlet. Therefore,a finite element stress analysis of the tube inlet with heat exchange tubes and welding seams was made,and an experimental investigation was made of the fatigue strength of the welding between the tubes and the tube sheet.
BURST ANALYSIS OF HIGH TEMPERATURE RE-HEATER PIPE OF POWERSTATION

刘高杰,李希超,任相文

DOI: https://doi.org/10.3969/j.issn.1001-4012.2003.07.009

2003-01-01

Abstract:The burst of high temperature re-heater pipe of powerstation occured when it operating over 30000 hours. It causes a lot of enormous losses. This article researchs the cause of cracking by means of macroscopic inspection, mechanical property testing etc. It was found that the cracking is induced by the partial superheat and superpressure. We put forward a proposal for improving the management of this eguipment.
Experimental and simulative failure analysis of reformer furnace outlet manifolds serviced in aromatic plant

xiaowei wang,jianqun tang,jianming gong,luyang geng,yong jiang,hao liu

DOI: https://doi.org/10.1016/j.engfailanal.2015.08.014

IF: 4

2015-01-01

Engineering Failure Analysis

Abstract:Reformer furnace hot outlet manifold is a critical component in aromatic plants. Unfortunately, a hot outlet manifold used in Nanjing YPC Refining & Chemical Co., Ltd. failed after it has been in service for only 2years. In the present paper, a failure analysis of the failed hot outlet manifold was performed by careful visual observation, mechanical properties tests, chemical content examination, microstructural analysis and microchemical analysis of fine precipitates. Finite element method (FEM) considering creep effect was also employed to define the evolution of critical region. Experimental results showed that the failure was a combination of overheating and high stress concentration. Exposing it to excessive temperatures at high stress significantly accelerated the creep rate, thus, leading to the premature failure. FEM analysis showed that hoop stress generated by the work inner pressure was the main reason leading to the crack initiated and propagated along axial direction of the manifold. Moreover, sequence of the failure region achieved by the simulation correlated well with the experimental analysis. To prevent the failure, better control of operating temperature was strongly recommended.
SIMULATION AND ANALYSIS ABOUT WORN-OUT ON CONNECTING PIPE OF LOW-PRESSURE REHEATER FOR A BOILER OF 600 MW UNIT

李相鹏,高增梁,陈江,周昊,岑可法

DOI: https://doi.org/10.3969/j.issn.1002-3364.2009.02.015

2009-01-01

Abstract:By adopting three-dimentional model,the simulation and analysis of worn-out on connecting pipe bundle of low-pressure reheater nearby the furnace outlet suffured from gas-phase flow field distribustion,movement of flyash,and concentration distribution etc.in the flue duct of boiler concerning 600 MW unit have been carried out.Results show that the flue gas velocity,particle's concentration and average collision velocity of particles nearby the furnace outlet all are larger due to influence of solid-gas two-phase flow distribution in the flue duct,thereby,the velocity of wornout on connecting pipes of the low-pressure reheater is also larger.It is recommended to install wornout-resistant covers of 6 mm thickness onto the windward surface of horizontal I-shaped pipe bundle of the low-pressure reheater between bottom of the first row connecting pipe and the other connecting pipes,as well as installing wornout-resitant covers with 3 mm thickness onto the other remained parts.
Failure Analysis on Abnormal Leakage of Shell and Tube Heat Exchanger in Specialty Chemical Plant

Si -Yuan Ma,Tong -Tong Bi,Yi Gong,Zhen-Guo Yang

DOI: https://doi.org/10.1016/j.engfailanal.2022.106859

IF: 4

2023-01-01

Engineering Failure Analysis

Abstract:The shell and tube heat exchanger has been widely used in the chemical industry. However, because of complex operating conditions, the heat exchanger tubes sometimes are leaked. This paper conducted in-depth failure analysis on abnormal leakage of several tubes of a shell and tube heat exchanger, which had been used for nine years in a methyl methacrylate production facility. In order to find out the root cause of the failure, chemical analysis, metallographic structure inspection and morphology observation of the leakage tubes were carried out. The composition and properties of the tube scales were analyzed by X-ray fluorescence spectroscopic analysis (XRF), X-ray diffraction analysis (XRD), thermogravimetric analysis (TGA), and energy spectrum analysis (EDS). The micro-zone features of the leaked tubes were observed with three-dimensional stereo microscope (3D-SM) and scanning electron microscope (SEM). According to the testing results and the actual operating conditions of the heat exchanger, the root cause of abnormal leakage of the tubes was finally determined. The key finding was that the terephthalic acid gas was suddenly desublimated into solid particles while its temperature was about 300 degrees C. Thus, the gas containing terephthalic acid particles caused erosion wear, abrasive wear and local corrosion onto the inlet side of the heat exchanger, leading to abnormal leakage of the tubes. Finally, some suggestions were put forward for the heat exchanger, which were also conducive to the safe operation and failure prevention of similar equipment.
Experiment and Investigation of Overheating Problem of 300MW Boiler's HT Reheater

王英涛,丘纪华,陈刚,周英彪,陈越,赵小峰

DOI: https://doi.org/10.3969/j.issn.1005-006x.2005.06.014

2005-01-01

Abstract:The No.1 300MW boiler in Zhanjiang Power Plant has had the problems of local overheating of high temperature reheater and large steam temperature deviation at the exit of reheaters for a long time.According to the cold test of flow field at the high temperature reheaters' entrance and exit and the hot test of temperature field at it's entrance,the cause of reheater's overheating and steam temperature deviation is analyzed and an explanation associating with the structure of reheater's tubes is made.
Cause analysis of elbow crack for header's connecting tubes of boiler's reheater concerning 300 mw unit

LIU Fa-sheng,CHEN Gang,WU Qi-xing

DOI: https://doi.org/10.3969/j.issn.1002-3364.2007.10.019

2007-01-01

Abstract:The elbow behind micro-spray desuperheater of boiler no.2 in one power plant has cracked many times,seriously affecting operation of the unit.Through inspection of the pipes,analysis of coal quality,and cold-state test of the reheater,it is believed that the crack of elbow is a typical thermal fatigue crack,resulting from deviation of actual coal sort from the designed coal sort,and temperature deviation of flue gas at outlet of the furnace,thus,leading to overtemperature of the heating surface,and frequently putting desuperheating water into service.Based on these,measures and recommendations,such as retrofitting the secondary air into reverse tangential firing,enhancing the feed-water and steam quality,improving quality of furnace-incoming coal and atomizing effectiveness of the nozzles,etc.,have been put forward.
Failure Analysis for the Reboiler of Regenerator

轩福贞,王正东,马春伟,董绍平,严伟丽

DOI: https://doi.org/10.3969/j.issn.1001-4837.2004.04.013

2004-01-01

Abstract:The failure causes of a reboiler of the regenerator in a certain refinery was investigated. From the results of spot inspection, element analysis of the materials, metallograpghic analysis and the ingredients analysis of the corrosion production, it was concluded that the pitting on the stainless steel pipes of the heat exchanger is caused by the H 2S and CO 2 in conjunction with the scouring of the medium in the reboiler. While for the local corrosion of the bolts, it was the joint result of the high speed scouring of the steam and the H 2S corrosion. Finally, the corresponding countermeasures and improvements were suggested according to the above results.
Failure analysis of a rapid quench boiler for ethylene cracker

Zhihong Duan,Weiqi Lian,Pujie Zhan,Junde Song,Canyin Li,Xiangji Yang,Bingjiang Chen,Yunrong Lyu

DOI: https://doi.org/10.1016/j.heliyon.2024.e33961

IF: 3.776

2024-07-02

Heliyon

Abstract:The corrosion and leakage issues of rapid quench boilers have become increasingly prominent in ethylene plants, significantly disrupting the regular functioning of equipment. In pursuit of a more efficacious corrosion protection strategy, a study was conducted on the heat exchange tubes experiencing corrosion leakage in the quenching boiler of a petrochemical company. By means of macroscopic observation, chemical composition analysis, mechanical property analysis, metallographic analysis, fracture surface morphology observation, and energy spectrum analysis, combined with on-site process parameters, a comprehensive analysis of the failure causes of the corroded leakage sites was conducted. It was concluded that the perforation of the heat exchange tubes was caused by high-temperature oxygen corrosion and oxidation induced by scale accumulation, and reasonable countermeasures were proposed. According to X-ray diffraction analysis (XRD), it was found that the scale mainly consisted of Fe2O3 and Fe3O4, and the scale formation time was relatively long. It is speculated that the accumulation of scale is caused by the rust from the upstream equipment pipelines of the boiler water being carried into the quenching boiler with the fluid flow and accumulating at this location. Regarding the heat exchange tubes, the primary causes of failure are high-temperature oxygen corrosion and oxidation. To verify whether the relevant reactions can occur spontaneously, the critical transition temperature of the reactions is calculated using the free entropy function method. The calculated critical temperature for the occurrence of high-temperature oxygen corrosion and oxidation in the heat exchange tubes under failure conditions is determined to be T ＜ 1058 K ~ 785 °C. Therefore, under the conditions of heat exchange tube failure, high-temperature oxygen corrosion and oxidation can occur spontaneously.
Failture Analysis of Welded Joint on Superheater of a 670t/h Boiler

Wang Chang-you,Li Chun-wen,Qin Dong

2008-01-01

Abstract:The causes leading to failure of welded joint on high temperature superheater of a boiler have been tested and analysed,Find out the reason of the failure.According to the experimental results,the preventive was presented.
Analysis of Causes and Protective Measures against Corrosion Perforation in the Shell-Side Outlet Flange of a Sour Water Steam Heater

Haiming Liang,Zhihong Duan,Weiming Li

DOI: https://doi.org/10.3390/coatings14030306

IF: 3.236

2024-03-02

Coatings

Abstract:Heat exchangers, as essential devices for facilitating heat transfer, have found a variety applications in various industries. However, the occurrence of corrosion-related failures in real-world scenarios remains a prevalent problem that can lead to catastrophic incidents. This paper investigates the problem of corrosion perforation on the outlet flange of a heat exchanger in a sour steam stripper from a petrochemical company. Failure analysis was performed using physical testing and chemical analysis, metallographic examination, microscopic observation, and energy spectrum analysis. Intergranular corrosion experiments and flow calculations were performed to verify the analysis. The results indicate that the main cause of the flange corrosion perforation was the formation of a highly concentrated NH4HS aqueous solution during the cooling process of the NH3, H2S, and water vapor in the fluid passing through the heat exchanger, and the velocity was too high, which triggered alkali-sour water washout corrosion. To prevent the recurrence of similar corrosion perforations, recommendations for material and process optimization are proposed to effectively reduce the safety production risks in refinery units and provide valuable information for the safe long-term operation of a sour steam stripper.

materials science, multidisciplinary,physics, applied, coatings & films

Study of the Reason and Measure on One 300MW Reheat Pipe Weld Bead's Blasting & Leaking

Cause Analyses of the Weld Seam Cracks of a Prehydrogenating Reactor

Study on Stress Intensity of Welding Parts of Small Dlameter Tube to Reheater in Coal-burning Thermo-electric Factory with 200 MW Power

Cause and Remedy for Cracks in Weld Seams of Reheater Sealing Plate of Wall Type for 350 MW Power Generating Set Boiler

Reason Analysis and Countermeasures for Leakage of Middle-pressure Waste Heat Boiler

Analysis of Invalidation Mechanism of Reheater of 1100t/h Boiler

Analysis of Frequent Tube Burst of High Temperature Reheater in 600 MW Unit

Analysis on the cause of crack in connection pipeline of subcritical boiler reheater

Cause Analysis and Improvement Measures for Pipeline Cracking of 9Cr-1Mo Material

Treatment and Analysis on Pipe Explosion of Low-Temperatme Reheater of "W" Flame Boiler

Analysis of the Vibration Damage Mechanism of the Tube Bundles of a Glycol Re-Boiler

BURST ANALYSIS OF HIGH TEMPERATURE RE-HEATER PIPE OF POWERSTATION

Experimental and simulative failure analysis of reformer furnace outlet manifolds serviced in aromatic plant

SIMULATION AND ANALYSIS ABOUT WORN-OUT ON CONNECTING PIPE OF LOW-PRESSURE REHEATER FOR A BOILER OF 600 MW UNIT

Failure Analysis on Abnormal Leakage of Shell and Tube Heat Exchanger in Specialty Chemical Plant

Experiment and Investigation of Overheating Problem of 300MW Boiler's HT Reheater

Cause analysis of elbow crack for header's connecting tubes of boiler's reheater concerning 300 mw unit

Failure Analysis for the Reboiler of Regenerator

Failure analysis of a rapid quench boiler for ethylene cracker

Failture Analysis of Welded Joint on Superheater of a 670t/h Boiler

Analysis of Causes and Protective Measures against Corrosion Perforation in the Shell-Side Outlet Flange of a Sour Water Steam Heater