Abstract:<p>For some π type boilers with four-corner tangential and deep air staged low nitrogen combustion technology, under full load condition, the steam temperature deviation for both sides of reheater outlet can reach as high as 15 ℃. The left and right cross arrangement of steam between two stage reheaters increases the steam temperature deviation at the outlet, and the large amount input of desuperheating water makes the economic efficiency of the unit decrease. A flue gas residual rotation adjusting experiment for a 660 MW ultra-supercritical boiler was carried out by adjusting the level and up and down swing angle of the separated overfire air nozzle, and the grid method was applied to measure the radiation intensity for particles at the high-temperature reheater area according to the principle of radiation spectrum. The results show that there exists strong visible radiation in this area. Under the 600 MW-load condition, the radiation heat transfer of particle accounts for 25.95% of the total heat absorption of the high-temperature superheater and particle combustion still exists. In addition, the combustion share accounts for about 1.83% of the received carbon content of coal. The particle temperature and emittance data fitted from the Planck's law indicate that the high-temperature particles are enriched at single side due to the inertial effect of residual rotation of flue gas. The residual rotation momentum of the separated over-fire air is insufficient to balance the temperature rise of both sides of the low-temperature reheater. Therefore, a new type of combustion system rebuild principle of changing a five-layer Separated Over-fire Air (SOFA) nozzle to two-sections of six-layer SOFA nozzle is proposed to mitigate the combustion delay of pulverized coal particles and the wall-type tangent circle arrangement of the upper separated over-fire air nozzle, improving the residual rotation momentum of flue gas.</p>

SIMULATION AND ANALYSIS ABOUT WORN-OUT ON CONNECTING PIPE OF LOW-PRESSURE REHEATER FOR A BOILER OF 600 MW UNIT

Study on Stress Intensity of Welding Parts of Small Dlameter Tube to Reheater in Coal-burning Thermo-electric Factory with 200 MW Power

Safety Testing and Analysis of the Header of the Drawn Boiler with a Small Diameter and a Large Wall Thickness

Treatment and Analysis on Pipe Explosion of Low-Temperatme Reheater of "W" Flame Boiler

Experimental and simulative failure analysis of reformer furnace outlet manifolds serviced in aromatic plant

Analysis of the Vibration Damage Mechanism of the Tube Bundles of a Glycol Re-Boiler

Analysis on the cause of crack in connection pipeline of subcritical boiler reheater

Steam Temperature Characteristics in Boiler Water Wall Tubes Based on Furnace CFD and Hydrodynamic Coupling Model

STUDY ON WORN-OUT RESULTING FROM IMPACT OF FLY ASH PARTICLES ONTO SMOOTH TUBE BUNDLES WITH IN-LINE ARRANGEMENT

Experiment and Investigation of Overheating Problem of 300MW Boiler's HT Reheater

ANALYSIS OF TEMPERATURE FIELD AND THERMAL STRESS FOR EXTERNALLY CONNECTED PIPE SOCKETS OF REHEATER BY USING THE FINITE ELEMENT METHOD

Analysis and Calculation of Structure Strength of Hot Gas Duct in HTR-PM

Analysis of Causes and Protective Measures against Corrosion Perforation in the Shell-Side Outlet Flange of a Sour Water Steam Heater

Cause analysis of elbow crack for header's connecting tubes of boiler's reheater concerning 300 mw unit

Thermal deviation analysis of high-temperature reheater for single-tangential π type boiler

Temperature Field Simulation and Analysis of Fire Tube Overheating Caused by Fouling of Heating Furnace

Creep Rupture Time Predication of a Superheater Wall in a Circulating Fluidized Bed Boile

Failture Analysis of Welded Joint on Superheater of a 670t/h Boiler

Analysis of Main Influencing Factors of the Wastewater Evaporation in Flue Duct

Numerical Study of Supercritical Opposed Wall-Fired Boiler Furnace Temperature and High-Temperature Heating Surface Stress under Variable Load Operation

Numerical study of particle deposition characteristics in a new type of reinforced pipe