Abstract:In this study, La 2 O 3 nanoparticles were incorporated into a tungsten (W) matrix to enhance the microstructure and properties of pure W. The selective laser melting (SLM) process for W-2wt% La 2 O 3 was optimized, and the influence of SLM processing parameters on the relative density and internal defects of the samples was examined. Challenges such as uneven powder layering and layer-by-layer thickening during the SLM process were addressed by incorporating a homogeneous material support formed with low laser energy density beneath the sample. This approach widened the process window for sample formation, resulting in a 2.38% increase in the average relative density of supported samples compared to unsupported ones. With optimized parameters of 240W laser power, 200mm/s scanning speed, and 80μm hatch spacing, the sample achieved a relative density of 98.32% with minimal internal pores, though some microcracks remained. Further investigation revealed that surface roughness decreased with increasing laser power and scanning speed. High laser power combined with low scanning speed yielded good surface quality. Under conditions of high relative density (over 96%), samples processed with low laser power and high scanning speed (200W, 200mm/s) exhibited fine and uniform grain morphology, few internal defects, and excellent mechanical properties, with a microhardness of 474HV and a compressive strength of 2237MPa.

Microstructures and Properties of W-Lu2O3 Composites Strengthened with Nb and C Trace Elements

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Microstructure and Properties of La2O3 Doped W Composites Prepared by a Wet Chemical Process

Fabrication of W-Cu/Lu2O3 Composites with High Strength and Electrical Conductivity Prepared by Electroless Plating and Powder Metallurgy

Effect of Doped Niobium on the Microstructure and Properties of W–Nb/TiC Composites Prepared by Spark Plasma Sintering

Selective laser melting of lanthanum oxide-reinforced tungsten composites: microstructure and mechanical properties

Effect of Doped Lu2o3 on the Microstructures and Properties of Tungsten Alloy Prepared by Spark Plasma Sintering

Study on forming process and performance of nano-La 2 O 3 reinforced tungsten-based composites by selective laser melting

Microstructure and performance of rare earth element-strengthened plasma-facing tungsten material

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering

Influence of Nano-Sized La2O3 Addition on the Sintering Behavior and Mechanical Properties of WC–La2O3 Composites

The Microstructure and Mechanical Properties of Carbon Nanotube-Reinforced W-Matrix Composites

Microstructure and mechanical properties of MoNbW(TaC)x composites

Fabrication and characterization of W/Cu/Ni-based high specific gravity alloy with Zr and Ti combined addition

Investigation of microstructure and irradiation behavior of W–Nb/Ti composites prepared by spark plasma sintering

Influence of La2O3 Addition on Hardness, Flexural Strength and Microstructure of Hot-Pressing Sintered WC–MgO Bulk Composites

Fabrication of W–Cu/CeO2 Composites with Excellent Electric Conductivity and High Strength Prepared from Copper-Coated Tungsten and Ceria Powders

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Effect of Rare Earth Oxide Addition on the Microstructure and Properties of Ultrafine Grain W-20Cu Composites

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites