Abstract:In this study, La 2 O 3 nanoparticles were incorporated into a tungsten (W) matrix to enhance the microstructure and properties of pure W. The selective laser melting (SLM) process for W-2wt% La 2 O 3 was optimized, and the influence of SLM processing parameters on the relative density and internal defects of the samples was examined. Challenges such as uneven powder layering and layer-by-layer thickening during the SLM process were addressed by incorporating a homogeneous material support formed with low laser energy density beneath the sample. This approach widened the process window for sample formation, resulting in a 2.38% increase in the average relative density of supported samples compared to unsupported ones. With optimized parameters of 240W laser power, 200mm/s scanning speed, and 80μm hatch spacing, the sample achieved a relative density of 98.32% with minimal internal pores, though some microcracks remained. Further investigation revealed that surface roughness decreased with increasing laser power and scanning speed. High laser power combined with low scanning speed yielded good surface quality. Under conditions of high relative density (over 96%), samples processed with low laser power and high scanning speed (200W, 200mm/s) exhibited fine and uniform grain morphology, few internal defects, and excellent mechanical properties, with a microhardness of 474HV and a compressive strength of 2237MPa.

Microstructure and Properties of La2O3 Doped W Composites Prepared by a Wet Chemical Process

Microstructures and Properties of W-Lu2O3 Composites Strengthened with Nb and C Trace Elements

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Effect of Doped Lu2o3 on the Microstructures and Properties of Tungsten Alloy Prepared by Spark Plasma Sintering

Selective laser melting of lanthanum oxide-reinforced tungsten composites: microstructure and mechanical properties

Fabrication of W–Cu/La2O3 Composite Powder with a Novel Pretreatment Prepared by Electroless Plating and Its Sintering Characterization

Study on forming process and performance of nano-La 2 O 3 reinforced tungsten-based composites by selective laser melting

Influence of Nano-Sized La2O3 Addition on the Sintering Behavior and Mechanical Properties of WC–La2O3 Composites

Influence of La2O3 Addition on Hardness, Flexural Strength and Microstructure of Hot-Pressing Sintered WC–MgO Bulk Composites

Effect of La2O3 content on the densification, microstructure and mechanical property of W-La2O3 alloy via pressureless sintering

Effects of doping route on microstructure and mechanical properties of W−1.0wt.%La2O3 alloys

Microstructure and Properties of Tungsten–samarium Oxide Composite Prepared by a Novel Wet Chemical Method and Spark Plasma Sintering

Microstructure and Mechanical Properties of W-Al2O3 Alloy Plates Prepared by a Wet Chemical Method and Rolling Process

Development and Characterization of a Novel Fine-Grained W–Ni–Mn–Mo Alloys with La2O3 Addition Prepared Via Low-Temperature Sintering

Microstructure and Properties of W/Sm2O3 Composites Prepared Spark Plasma Sintering

Fabrication of W-Cu/Lu2O3 Composites with High Strength and Electrical Conductivity Prepared by Electroless Plating and Powder Metallurgy

Effect of La 2 O 3 on Microstructure, Mechanical and Tribological Properties of Ni-W Coatings

Effect of Rare Earth Oxide Addition on the Microstructure and Properties of Ultrafine Grain W-20Cu Composites

Lanthanum Hydride Doped Tungsten-Based Coating Fabricated by Supersonic Atmospheric Plasma Spraying

Excellent performance of W–Y2O3 composite via powder process improvement and Y2O3 refinement

Ultrafine grained WC-10FeCoCu cemented carbides doped with La 2 O 3 prepared by spark plasma sintering