Abstract:A new two-step spark plasma sintering (TSS) process with low-temperature pre-sintering and high-temperature final sintering has been successfully applied to prepare the tungsten-particle (Wp)-reinforced bulk metallic glass composites (Wp/BMGCs). Compared to normal spark plasma sintering (NS), the densification rate and relative density of Wp/BMGCs can be improved by selecting TSS with appropriate sintering pressure in the low temperature pre-sintering stage. However, the compressive strength and plastic strain of 30%Wp/BMGCs prepared by TSS are both higher than those of the samples prepared by NS. The TSS process can significantly enhance the compressive strength of 30%Wp/BMGCs by 12% and remarkably increase the plastic strain by 50%, while the trend is completely opposite for 50%Wp/BMGCs. Quasi-in situ experiments and finite element simulations reveal that uneven temperature distribution among particles during low-temperature pre-sintering causes local overheating at contact points between particles, accelerating formation of sintering neck between particles and plastic deformation of Wp. When the volume fraction of Wp is low, TSS can improve the interface bonding between particles by increasing the number of sintering necks. This makes the fracture mode of Wp/BMGCs being predominantly transgranular fracture. However, as the volume fraction of Wp increases, the adverse effects of Wp plastic deformation are becoming more and more prominent. The aggregated Wp tends to form a solid "cage structure" that hinders the bonding between particles at the interface; correspondingly, the fracture behavior of Wp/BMGCs is mainly dominated by intergranular fracture. Additionally, reducing the sintering pressure during the low-temperature pre-sintering stage of TSS has been shown to effectively decrease plastic deformation in Wp, resulting in a higher degree of densification and better mechanical properties.

Microstructure and Properties of Tungsten–samarium Oxide Composite Prepared by a Novel Wet Chemical Method and Spark Plasma Sintering

Microstructure and Properties of W/Sm2O3 Composites Prepared Spark Plasma Sintering

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

High-pressure Preparation of Bulk Tungsten Material with Near-Full Densification and High Fracture Toughness

Chemically Produced Tungsten–praseodymium Oxide Composite Sintered by Spark Plasma Sintering

Development of Tungsten-Based Materials by Different Sintering Techniques

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Effect of Doped Lu2o3 on the Microstructures and Properties of Tungsten Alloy Prepared by Spark Plasma Sintering

Fabrication of W–1 Wt.% TiC Composites by Spark Plasma Sintering

Chemical Synthesis and Oxide Dispersion Properties of Strengthened Tungsten Via Spark Plasma Sintering

Synthesis of W-TiC composite powders by wet-chemical process and its sintering behavior by SPS

Microstructure and Properties of La2O3 Doped W Composites Prepared by a Wet Chemical Process

Microstructural Evolution and Mechanical Properties of Spark Plasma Sintering of Tantalum-Tungsten Alloy

The microstructure and deformation behavior of W-SiC composites via spark plasma sintering

Preparation and Characteristics of W–1 Wt.% TiC Alloy Via a Novel Chemical Method and Spark Plasma Sintering

Excellent performance of W–Y2O3 composite via powder process improvement and Y2O3 refinement

SPS Sintering & Joining Based on Preparation of Tungsten-Molybdenum Composite Target

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

An investigation of the peculiarities of high-speed sintering of plasma chemically synthesized tungsten carbide nanopowders with increased oxygen content

Preparation of Tungsten-Particle-reinforced Zr-based Bulk Metallic Glass Composites by Two-Step Spark Plasma Sintering: Microstructure Evolution, Densification Mechanism and Mechanical Properties

Preparation of Ultrafine Tungsten-Molybdenum Composite Powder and Its Sintering Behavior