Abstract:Development of metallic glasses is hindered by the difficulties in manufacturing bulk parts large enough for practical applications. Spark plasma sintering (SPS) has emerged as an effective consolidation technique in the formation of bulk metallic glasses (BMGs) from melt-spun ribbons. In this study, Mg65Zn30Ca5 melt-spun ribbons were sintered at prolonged sintering times (15 min to 180 min) via SPS under a pressure of 90 MPa and at a temperature of 150 °C (which is below the crystallization temperature), to provide an insight into the influence of sintering time on the consolidation, structural, and biodegradation behavior of Mg-BMGs. Scanning Electron Microscopy was used to characterize the microstructure of the surface, while the presence of the amorphous phase was characterized using X-ray diffraction and Electron Backscatter Diffraction. Pellets 10 mm in diameter and height with near-net amorphous structure were synthesized at 150 °C with a sintering time of 90 min, resulting in densification as high as 98.2% with minimal crystallization. Sintering at extended durations above 90 min achieved higher densification and resulted in a significant amount of local and partial devitrification. Mechanical properties were characterized via compression and microhardness testing. Compression results show that increased sintering time led to better structural integrity and mechanical properties. Notably, SPS150_90 displayed ultimate compressive strength (220 MPa) that matches that of the cortical bone (205 MPa). Corrosion properties were characterized via potentiodynamic polarization with Phosphate Buffered Solution (PBS). The results suggest that the sintered samples have significantly better corrosion resistance compared to the crystalline form. Overall, SPS150_90 was observed to have a good balance between corrosion properties (10× better corrosion resistance to as-cast alloy) and mechanical properties.

Preparation of Tungsten-Particle-reinforced Zr-based Bulk Metallic Glass Composites by Two-Step Spark Plasma Sintering: Microstructure Evolution, Densification Mechanism and Mechanical Properties

Preparation and mechanical properties of tungsten-particle-reinforced Zr-based bulk-metallic-glass composites

Microstructure and Mechanical Properties of Zr-Based Metallic Glass Composites with Size-Variable Tungsten Reinforcements

High-pressure Preparation of Bulk Tungsten Material with Near-Full Densification and High Fracture Toughness

Mechanical Properties and Weibull Reliability Analysis of Tungsten-Particle Reinforced Zr-based Bulk Metallic Glass Composites

Preparation, Microstructure, and Mechanical Properties of Bulk Metallic Glass Composite Containing In Situ-Formed Dendrites and Ex Situ Tungsten Particles

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Development of Tungsten-Based Materials by Different Sintering Techniques

Sps Sintering Connection Based On The Preparation Of Tungsten-Molybdenum Composite Target

SPS Sintering & Joining Based on Preparation of Tungsten-Molybdenum Composite Target

Dynamic compressive properties of two tungsten structure reinforced Zr-based metallic glass composites at different temperatures

Toughening mechanism of Zr-based and Cu-based bulk metallic glasses composites by TiNb particle

Synthesis and Property of Short Tungsten Fibre/zr-Based Metallic Glass Composite

Martensitic Transformation and Plastic Deformation of TiCuNiZr-Based Bulk Metallic Glass Composites

Suppressing Pore-Boundary Separation During Spark Plasma Sintering of Tungsten

Ti Particles Dispersed Ti-Based Metallic Glass Matrix Composite Prepared by Spark Plasma Sintering

Microstructure, densification and mechanical properties of in situ TiBw/Ti2AlNb composites fabricated by spark plasma sintering

Synthesis and properties of tungsten balls/Zr-base metallic glass composite

Deformation Behavior of Tungsten Wires Enhanced Zr-Based Bulk Metallic Glass Composite at High Strain Rate

Fabrication of Ni<sub>52.5</sub>Nb<sub>10</sub>Zr<sub>15</sub>Ti<sub>15</sub>Pt<sub>7.5</sub> Bulk Metallic Glassy Matrix Composite Containing Dispersed ZrO<sub>2</sub> Particulates by Spark Plasma Sintering

Enhancing Mechanical and Biocorrosion Response of a MgZnCa Bulk Metallic Glass through Variation in Spark Plasma Sintering Time