Abstract:Method of soft metal (Cu) strengthening of Ti3SiC2 was conducted to increase the hardness and improve the wear resistance of Ti3SiC2. Ti3SiC2/Cu composites containing 15 vol.% Cu were fabricated by Spark Plasma Sintering (SPS) in a vacuum. The effect of the sintering temperature on the phase composition, microstructure and mechanical properties of the composites was investigated in detail. The as-synthesized composites were thoroughly characterized by scanning electron micrography (SEM), optical micrography (OM) and X-ray diffractometry (XRD), respectively. The results indicated that the constituent of the Ti3SiC2/Cu composites sintered at different temperatures included Ti3SiC2, Cu3Si and TiC. The formation of Cu3Si and TiC originated from the reaction between Ti3SiC2 and Cu, which was induced by the presence of Cu and the de-intercalation of Si atoms Ti3SiC2. OM analysis showed that with the increase in the sintering temperature, the reaction between Ti3SiC2 and Cu was severe, leading to the Ti3SiC2 getting smaller and smaller. SEM measurements illustrated that the uniformity of the microstructure distribution of the composites was restricted by the agglomeration of Cu, controlling the mechanical behaviors of the composites. At 1000 °C, the distribution of Cu in the composites was relatively even; thus, the composites exhibited the highest density, relatively high hardness and compressive strength. The relationships of the temperature, the current and the axial dimension with the time during the sintering process were further discussed. Additionally, a schematic illustration was proposed to explain the related sintering characteristic of the composites sintered by SPS. The as-synthesized Ti3SiC2/Cu composites were expected to improve the wear resistance of polycrystalline Ti3SiC2.

Fabrication of W–1 Wt.% TiC Composites by Spark Plasma Sintering

Preparation and Characteristics of W–1 Wt.% TiC Alloy Via a Novel Chemical Method and Spark Plasma Sintering

Synthesis of W-TiC composite powders by wet-chemical process and its sintering behavior by SPS

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Spark plasma sintering of TiC ceramic with tungsten carbide as a sintering additive

Densification, Microstructure and Mechanical Performance of TiC/Fe Composites by Spark Plasma Sintering

Microstructure and mechanical properties of (Ti,W)C cermets prepared by ultrafast spark plasma sintering

Microstructure, densification and mechanical properties of in situ TiBw/Ti2AlNb composites fabricated by spark plasma sintering

Spark Plasma Sintering of W-10Ti High-Purity Sputtering Target: Densification Mechanism and Microstructure Evolution

Spark Plasma Sintering of W-10Ti Alloys: Microstructure, Properties and Grain Growth Kinetics

Microstructure, Mechanical Properties, and Sintering Behavior of Ti3O-Fe2TiO4-TiC Composites

Densification and Mechanical Properties of Tic by Sps-Effects of Holding Time, Sintering Temperature and Pressure Condition

The microstructure and deformation behavior of W-SiC composites via spark plasma sintering

Microstructure and Properties of TiN-reinforced W–Ti Alloys Prepared by Spark Plasma Sintering

Microstructure and Mechanical Properties of Composites Obtained by Spark Plasma Sintering of Ti3SiC2-15 vol.%Cu Mixtures

Microstructure and Properties of W/Sm2O3 Composites Prepared Spark Plasma Sintering

Fabrication of Ultra-Fine-Grained W-TiC Alloys by a Simple Ball-Milling and Hydrogen Reduction Method

Microstructure and Properties of Tungsten–samarium Oxide Composite Prepared by a Novel Wet Chemical Method and Spark Plasma Sintering

Investigation on microstructure and reinforcement mechanism of the TiC-reinforced W-matrix composite prepared by high-energy ball milling and spark plasma sintering

Fabrication and mechanical evaluation of SiC–TiC nanocomposites by SPS

Synthesis and characterization of extremely hard and strong (W,Ti,Ta)C cermet by spark plasma sintering