Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Preparation Of Al2o3-Sic Composite Powder From Kyanite Tailings Via Carbothermal Reduction Process

Preparation of β-Sialon /SiC composite powder by carbothermal reaction of coal-mine schist

Dilithium Dialuminium Trisilicate Crystalline Phase Prepared from Coal Fly Ash

Preparation and Sinterability of Submicron Titanium Carbide Powders Synthesized with Phenolic Resin As Carbon Source by Carbothermal Reduction

Preparation Of Nanocrystalline Silicon Carbide Powders By Carbothermal Reduction

Studies of synthesizing the SiC nanometer powders by chemical vapor reaction

Preparation of SiC Powders by Carbothermal Reduction with Bamboo Charcoal As Renewable Carbon Source

Carbothermal Reduction Nitridation of Fly Ash, Diatomite and Raw Illite: Formation of Nitride Powders with Different Morphology and Photoluminescence Properties

Preparation of beta sialon/SiC composite powder by carbothermal reaction of coal mine schist

Synthesis and Properties of Al4sic4 by Carbothermal Reduction

Preparation of Silicon Carbide Powder from Amorphous Silica and Investigation of Synthesis Mechanism

Synthesis of nanocrystalline silicon carbide powders

Rapid Synthesis of SiC Powders by Spark Plasma-Assisted Carbothermal Reduction Reaction

Synthesis and Characterization of Si/SiO2/SiC Composites Through Carbothermic Reduction of Rice Husk-based Silica

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Synthesis of SiC@SiO2 Nanocables Via a Catalyst-Free Carbothermal Reduction Method

Synthesis of Silicon Nitride/Silicon Carbide Nanocomposite Powders through Partial Reduction of Silicon Nitride by Pyrolyzed Carbon

Combustion synthesis of SiC/Al2O3 composite powders with SiC nanowires and their growth mechanism

Reactive Synthesis for Porous (Mo2/3Y1/3)2AlC Ceramics through Mo, Y, Al and Graphite Powders

In situ synthesis of Al2O3–SiC powders via molten-salt-assisted aluminum/carbothermal reduction method