Abstract:A technological route for recycling silicon slurry cutting waste (SSCW) as silicon source to prepare high purity silicon carbide as well as reducing the industry cost and avoiding the environmental pollution aroused by the waste was explored. The effect of Fe2O3, NaCl addition and smelting temperature on production of high quality SiC were studied. The existence of Fe element acts like a catalyst and contributes to the synthesis of SiC at relatively low temperatures (1550 °C). The excess of Fe element in the SSCW, however, would inhibit further improvement of the purity of the SiC product since Fe element would remain in the final product as Si-Fe alloy. Slight addition of salt was also verified to be positive for the improvement of SiC yield and purity. SiC product with a purity of more than 93 wt.% was obtained after acid leaching for the removal of Fe impurity and under the optimized conditions as NaCl addition of 7 wt.% and smelting temperature of 1850 °C. The thermodynamic analysis shows that a series of intermediate gas products (CO, SiO, SiO2) have been generated and taken an important role in the synthesis of SiC and excess carbon source is necessary for promoting the utilization of the SSCW since it can efficiently contribute to the formation of SiC and the intermediate products namely SiO and CO. The nucleation mechanism analysis indicates that both the original size and morphology of the carbon source and SiC particles have great influence on the forming particle size and morphology of the generated SiC since both can act as a nucleation center for a certain amount of SiC which is verified by the SEM analysis.

In situ synthesis of Al2O3–SiC powders via molten-salt-assisted aluminum/carbothermal reduction method

Revealing Salt-Expedited Reduction Mechanism for Hollow Silicon Microsphere Formation in Bi-Functional Halide Melts

In-situ Synthesis of Nanocrystalline TiC Powders, Nanorods, and Nanosheets in Molten Salt by Disproportionation Reaction of Ti(II) Species

Synthesis of Nano Sized Cr2AlC Powders by Molten Salt Method

Manipulation Of Phase And Microstructure At Nanoscale For Sic In Molten Salt Synthesis

Nanomaterials Via Solution Combustion Synthesis: a Step Nearer to Controllability

Recycle of silicon slurry cutting waste to prepare high purity SiC by salt-assisted carbothermic reduction

Synthesis of Stoichiometric Titanium Carbide by a Combination of Carbothermal Reduction and Molten Salt Method and Its Characterization

Molten Salt Dynamic Sealing Synthesis of MAX Phases (ti3alc2, Ti3SiC2 Et Al.) Powder in Air

Low temperature Pr 3 Si 2 C 2 ‐assisted liquid phase sintering of SiC with improved thermal conductivity

A novel sintering additive system for porous mullite-bonded SiC ceramics: High mechanical performance with controllable pore structure

The synthesis of high purity Ti3AlC2 MAX phase via molten salt method

Salt-templated strategy for well dispersed multi-component composites with morphologies ranging from millimeter to nano-scale

Salt Melt Synthesis of Ceramics, Semiconductors and Carbon Nanostructures.

Highly Efficient and Low-Temperature Preparation of Plate-Like ZrB₂-SiC Powders by a Molten-Salt and Microwave-Modified Boro/Carbothermal Reduction Method.

A-site cation and morphology control of KSr2Nb5O15 microcrystalline by a modified molten salt method

Preparation of Al4SiC4 with higher aspect ratio by a novel two-step method

Electrolytic synthesis of TiC/SiC nanocomposites from high titanium slag in molten salt

In‐situ synthesis of 15R‐Sialon from Al‐Si 3 N 4 ‐Al 2 O 3 composite at 1500°C via liquid‐phase sintering

Synthesis of Pure Bi<sub>12</sub>SiO<sub>20</sub> Powder by Molten Salt Method

Air-isolated stir casting of homogeneous Al-SiC composite with no air entrapment and Al4C3