Abstract:Chemical-mechanical planarization (CMP) represents the preferred technology in which both chemical and mechanical interactions are combined to achieve global planarization/polishing of wafer surfaces (wafer patterns from metal with a selective layer, in this paper). CMP is a complex process of material removal process by friction, which interferes with numerous mechanical and chemical parameters. Compared with chemical parameters, mechanical parameters have a greater influence on the material removal rate (MRR). The mechanical parameters manifest by friction force (Ff) and heat generated by friction in the CMP process. The Ff can be estimated by its monitoring in the CMP process, and process temperature is obtained with help of an infrared rays (IR) sensor. Both the Ff and the MRR increase by introducing colloidal silica (SiO2) as an abrasive into the selective layer CMP slurry. The calculated wafer non-uniformity (WNU) was correlated with the friction coefficient (COF). The control of Ff and of the slurry stability is important to maintain a good quality of planarization with optimal results, because Ff participates in mechanical abrasion, and large Ff may generate defects on the wafer surface. Additionally, the temperature generated by the Ff increases as the SiO2 concentration increases. The MRR of the selective layer into the CMP slurry showed a non-linear (Prestonian) behavior, useful not only to improve the planarization level but to improve its non-uniformity due to the various pressure distributions. The evaluation of the Ff allowed the calculation of the friction energy (Ef) to highlight the chemical contribution in selective-layer CMP, from which it derived an empirical model for the material removal amount (MRA) and validated by the CMP results. With the addition of abrasive nanoparticles into the CMP slurry, their concentration increased and the MRA of the selective layer improved; Ff and MRR can be increased due to the number of chemisorbed active abrasive nanoparticles by the selective layer. Therefore, a single abrasive was considered to better understand the effect of SiO2 concentration as an abrasive and of the MRR features depending on abrasive nanoparticle concentration. This paper highlights the correlation between friction and temperature of the SiO2 slurry with CMP results, useful to examine the temperature distribution. All the MRRs depending on Ef after planarization with various SiO2 concentrations had a non-linear characteristic. The obtained results can help in developing a CMP process more effectively.

Study of the Technical Parameters of CMP Process of LiNb03 Cubic Flake Machining Powder Metalized Parts

Study on the Chemo-mechanical Polishing Quality of LiNb03 Cubic Flake

Research on CMP Process Parameters Effect on Slurry Transport

Study on Optimum Process of CMP

Molecular Modeling of the Mechanical Effect in the Chemical Mechanical Polishing Process

Study on the Effecting Factors of the Removal Rate During CMP Process

Good-Quality and High-Efficiency Dicing for Thick LiNbO3 Wafers Using Picosecond Laser Pulses

Mechanism and Applications of Chemical and Mechanical Polishing

Effects of Nano-Scale Particles in Chemical Mechanical Polishing Process

Multiparameter Optimization Design of Chemical Mechanical Polishing for Planar Optics

Analysis on Pad Effects in Chemical Mechanical Polishing

Research on the key technology for processing efficiency improvement of aluminum alloy mirror chemical mechanical polishing

Research Progress of Material Removal Mechanism in Chemical Mechanical Planarization for Metal Interconnection Layer of Chips

Mechanical Model of Nanoparticles for Material Removal in Chemical Mechanical Polishing Process

Slurry Parameters Effect on Chemical-Mechanical Planarisation (CMP) of Deposited Silver (ag) on Chips

Optimization of Design of Experiment for Chemical Mechanical Polishing of A 12-Inch Wafer

The Effects of Friction and Temperature in the Chemical-Mechanical Planarization Process

Technological parameter optimization and quality effects on solid-liquid phase abrasive flow polishing

The Process Optimization Analysis of CBN Abrasive Cu-Sn-Ti Coating Fabrication via the Ultrasonic-Vibration-Assisted Laser Cladding Method

Preparation of Composite Spherical Alumina Nanoparticles and Study on their CMP Performance

Chemical effects on the tribological behavior during copper chemical mechanical planarization