Abstract:Si3N4/SiC composites containing 0-30 vol% SiC were fabricated by pressureless sintering and sinter-post-HIPing method using fine Si3N4 and nano-sized SiC powders. Specimens reached full density (>96% theoretical density (th. d.)) except the composites made by pressureless sintering which contained a small amount of sintering additives or a large amount of SiC. All composites with 10 mass% sintering additives reached full density (similar to 99% th. d.) by sinter-post-HIPing. The addition of SiC particles greatly influenced the grain morphology of the Si3N4 matrix. The average grain thickness, length and aspect ratio decreased with increasing SiC content because of grain boundary pinning by SiC particles. Also the mechanical properties were markedly dependent upon the fraction of SiC particle reinforcement, as well as matrix grain size and porosity. When the materials were pressureless sintered, the strength of the composite increased with SiC additions below 20 vol%. Further increase in the SIC content resulted in a corresponding decrease in strength. Maximum strength of 1150 MPa was attained at 20 vol% SiC addition. The increase in strength by addition of SiC is due to decrease of grain size of Si3N4 matrix grain size, and the decrease by further increase in SiC content is caused by porosity and SiC agglomerate. On the other hand, toughness decreased monotonically with SiC content. The strength of all samples was enhanced by sinter-post-HIPing without any change in fracture toughness. The strength of sintered samples with 10-15 vol% SiC increased by similar to 20% to 1260 MPa by post-HIPing. The increase in strength by post-HIPing was interpreted as being due to a decrease flaw size.

Mechanical Properties of AlN-SiC Ceramic Composites Synthesized by Pressureless Sintering and Post-HIP Treatment.

Synthesis and properties of AIN-SiC-TiB2 ceramics by SHS-HIP

Synthesis of SiC-AIN ceramic alloy by reaction sintering and its HIP-densification

Sintering And Mechanical Properties Of Aln-Rich Ceramics In The Sic-Aln System

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Mechanical Properties of SiC-AlN Single-Phase Alloys and Two-Phase Composites.

Synthesis of SiC-AlN Powder and Characterization of Its HIP-Sintered Compacts.

Pressureless Sintering and High-Temperature Strength of SiC-AlN Ceramics

Synthesis and Properties of AlN-SiC-TiB2 Ceramics by SHS-HIP

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Preparation and mechanical properties of SiC-AlN ceramic alloy

Preparation of SiC-AlN Ceramic Alloy Powder by Direct Reaction Between Constituent Elements and Property Evaluation of Its Sintered Compacts.

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

Effect of composite sintering aids system on properties of pressureless sintered AlN ceramics

High-Temperature Strength of Sic-Aln Solid-Solutions and Composites As Evaluated by Small Punch Tests

High-temperature Deformation Behavior of SiC-AlN Ceramic Alloys with Fine-grained Microstructure.

Mechanical Properties of Ceramic–metal Composites by Pressure Infiltration of Metal into Porous Ceramics

Synthesis of SiC-AlN Ceramic Alloy Powder by the Direct Reactions Between the Constituent Elements.

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Fabrication of AlN-SiC-TiB2 Ceramics by Self-Propagating High Temperature Synthesis and Hot Isostatic Pressing