Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Synthesis of SiC-AIN ceramic alloy by reaction sintering and its HIP-densification

Mechanical Properties of AlN-SiC Ceramic Composites Synthesized by Pressureless Sintering and Post-HIP Treatment.

Synthesis of SiC-AlN Powder and Characterization of Its HIP-Sintered Compacts.

Synthesis of SiC-AlN Ceramic Alloy Powder by the Direct Reactions Between the Constituent Elements.

Preparation of SiC-AlN Ceramic Alloy Powder by Direct Reaction Between Constituent Elements and Property Evaluation of Its Sintered Compacts.

Synthesis and properties of AIN-SiC-TiB2 ceramics by SHS-HIP

Sintering And Mechanical Properties Of Aln-Rich Ceramics In The Sic-Aln System

Reaction Synthesis of SiC-AlN Ceramic Alloys

Mechanical synthesized nanocrystalline Ti/Al composite powders as precursor for Ti/Al alloy via reactive sintering

Preparation and mechanical properties of SiC-AlN ceramic alloy

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Synthesis and Properties of AlN-SiC-TiB2 Ceramics by SHS-HIP

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Hot Isostatically Pressed SiC‐AIN Powder Mixtures: Effect of Milling on Solid‐Solution Formation and Related Properties

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Effect of Ball-milling Time for Powder Mixing on the Thermomechanical Properties of SiC-AlN System Ceramics.

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

High-temperature Deformation Behavior of SiC-AlN Ceramic Alloys with Fine-grained Microstructure.

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Porous 2h‐silicon Carbide Ceramics Fabricated by Carbothermal Reaction Between Silicon Nitride and Carbon