Abstract:The surface Ga content for a CIGSe absorber was closely related to variation in the open-circuit voltage (VOC), while it was generally low on a CIGSe surface fabricated by two-step selenization. In this work, a solution-processed surface treatment based on spin-coating GaCl3 solution onto a CIGSe surface was applied to increase the Ga content on the surface. XPS, XRD, Raman spectroscopy, and band gap extraction based on the external quantum efficiency response demonstrated that GaCl3 post deposition treatment (GaCl3–PDT) can be used to enhance the Ga content on the surface of a CIGSe absorber. Meanwhile, a solution-processed surface treatment with KSCN (KSCN–PDT) was employed to form a transmission barrier for holes by moving the valence band maximum downward and decreasing the interface recombination between the CdS and CIGSe layers. Admittance spectroscopy results revealed that deep defects were passivated by GaCl3–PDT or KSCN–PDT. By applying the combination of GaCl3–PDT and KSCN–PDT, a champion device was realized that exhibited an efficiency of 13.5% with an improved VOC of 610 mV. Comparing the efficiency of the untreated CIGSe solar cells (11.7%), the CIGSe device efficiency with GaCl3–PDT and KSCN–PDT exhibited 15% enhancement.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c00270</a>.XPS peaks of Se 3p for the CIGSe absorbers untreated and treated by GaCl3–PDT, KSCN–PDT, and GaCl3&KSCN–PDT; Eg calculated from the transmittance of the CdS thin film; and UPS spectra for the CdS thin film (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c00270/suppl_file/am1c00270_si_001.pdf">PDF</a>).This article has not yet been cited by other publications.

Cu(In,Ga)Se2 solar cell with 16.7% active‐area efficiency achieved by sputtering from a quaternary target

13.6%-Efficient Cu(In,Ga)Se-2 Solar Cell with Absorber Fabricated by Rf Sputtering of (In,ga)(2)se-3 and Cu Se Targets

Preparation of Cu(In,Ga)Se2 Thin Film by Sputtering from Cu(In,Ga)Se2 Quaternary Target

10.3%-Efficient Submicron-Thick Cu(In,Ga)Se2 Solar Cells with Absorber Fabricated by Sputtering In2Se3, CuGaSe2 and Cu2Se Targets

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Fabricating Cu(In,Ga)Se2 (CIGS) Thin Films with Large Grains Based on the Quaternary CIGS Targets

Fabrication of Se-rich Cu(In1-XGaX)Se2 Quaternary Ceramic Target

Influences of Sulfurization on Performances of Cu(In,Ga)(Se,S)2 Cells Fabricated Based on the Method of Sputtering CIGSe Quaternary Target

The Relationships Between Electronic Properties and Microstructure of Cu(In,Ga)Se-2 Films Prepared by Sputtering from A Quaternary Target

The Effects of Selenium Content on Cu(Inga)Se-2 Thin Film Solar Cells by Sputtering from Quaternary Target with Se-Free Post Annealing

The Formation Mechanism of Cu(In0.7Ga0.3)Se-2 Nanoparticles and the Densification Trajectory of the Se-Rich Quaternary Target by Hot Pressing

One-Step Synthesis of Cu(In,Ga)Se-2 Absorber Layers by Magnetron Sputtering from A Single Quaternary Target

Influences of Ga Concentration on Performances of CuInGaSe2 Cells Fabricated by Sputtering-Based Method with Ceramic Quaternary Target

Ga2Se3 Treatment of Cu-rich CIGS Thin Films to Fabricate Cu-poor CIGS Thin Films with Large Grains and U-shaped Ga Distribution

Cu(In,Ga)Se-2 Solar Cells Fabricated by Sputtering from Copper-Poor and Selenium-Rich Ceramic Target with Selenium-Free Post Treatment

Efficiency improvement of electrodeposition-processed Cu(In,Ga)Se2 solar cell with widen surface bandgap by spin-coating In2S3 thin film

Efficiency enhancement of copper indium gallium selenide solar cells fabricated on polyimide foils with multiple metal layers

Two-stage method to enhance the grain size of Cu(In,Ga)Se2 absorbers based on sputtering quaternary Cu(In,Ga)Se2 target

New Solution-Processed Surface Treatment to Improve the Photovoltaic Properties of Electrodeposited Cu(In,Ga)Se 2 (CIGSe) Solar Cells

The Effects of Annealing Temperature on CIGS Solar Cells by Sputtering from Quaternary Target with Se-free Post Annealing

Multi-layer Strategy to Enhance the Grain Size of CIGS Thin Film Fabricating by Single Quaternary CIGS Target