Abstract:We report here a detailed characterization of the surface chemical states and morphology of polyimide (PI) films following modifications by plasma treatment and electroless copper deposition. NH3 and Ar plasma treatments have been successfully used to achieve morphological and chemical modification of the PI surface so that electroless copper plating can occur. The adhesion strength of the electroless copper to the PI surface was measured and correlated with the plasma-induced chemical and physical modifications of the PI surface. The NH3 plasma causes primarily chemical changes to the PI surface through creation of nitrogen moieties (i.e., –N =C< ) on the surface. The Ar plasma treatment brings about mainly physical changes to the surface (i.e., surface roughening). The combined-plasma treatment (Ar plasma followed by NH3 plasma) combines the desirable chemical and physical effects of each treatment, yielding a PI surface with higher roughness for physical anchoring of the copper and surface bonding sites (nitrogen and oxygen sites). During the electroless copper surface activation step with tin chloride and palladium chloride, tin bonds mainly with the oxygen on the surface, whereas palladium reacts with tin chloride as well as with the surface nitrogen. A direct relationship has been observed between surface palladium concentration and the abundance of the –N =C< sites on the surface. This suggests that the nitrogen radicals created during the NH3 plasma are incorporated into the surface and serve as bonding sites for the palladium. In the subsequent electroless Cu deposition, there was a direct correlation between the palladium surface concentration and Cu coverage. The adhesion strength of the electroless copper to the PI correlated well to the surface modifications and plasma treatment conditions. For the first time, a specific bonding configuration on the PI surface is shown to promote adsorption of palladium, which in turn promotes covalent bonding with Cu. The relative importance of surface roughness and chemical bonding on the adhesion strength is discussed.

Studies of Polyimide/copper Interface and Its Improvement by a Two‐component Primer

Preparation and imidization of polyimide composites filled with boron nitride

Surface Modification of Copper for Adhesion Promotion by Polybenzimidazole

Modification of Cu Nanoparticles with A Disulfide for Polyimide Metallization

Diffusion and Adhesion Properties of Cu Films on Polyimide Substrates

Interfacial Modification of Polymer/metal Joints by a Two-Component Coupling System of Polybenzimidazole and 2-Mercaptobenzimidazole

Adhesion property between low-thermal- expansion poly (benzoxazole-imide) film and ion-implanted copper

Complex-Induced Coupling Effect - Adhesion of Some Polymers to Copper Metal Promoted by Benzimidazole

Adhesive properties of deposited Cu films on colorless polyimide using high power impulse magnetron sputtering system

Nucleation and growth of low resistivity copper thin films on polyimide substrates by low-temperature atomic layer deposition

Synthesis and Characterization of Biphenyl Polyimide Containing Alkyl Sulfide Structure

Plasma Treatment and Surface Analysis of Polyimide Films for Electroless Copper Buildup Process

Adhesion Properties of Electroplating Process Between Polyimide and Metal Layer for Polymer/Metal Hybrid Bonding

Enhancing the bond strength of magnetron-sputtered copper layers on polyimide and polyether ether ketone surfaces through surface modification

Copper Metallization on the Surface-Modified Polyimide Films by Electroless Plating Method

Interpenetration Networked Polyimide–Epoxy Copolymer under Kinetic and Thermodynamic Control for Anticorrosion Coating

Plasma surface pretreatment to improve interfacial adhesion strengths of sputtered Cu on polyimide film

Photocatalytic Surface Modification of PI Film for Electroless Copper Plating

Adhesion promotion for epoxy resin/copper and polyimide/copper joints by a two‐component coupling system of poly(4‐vinylimidazole) and cystamine

Interlayer Design for Strong Adhesion in the Double-Layer Flexible Copper Clad Laminate Via Hipims Deposition

Studies of copper-catalysed degradation of epoxy coatings and a method for improving the durability of an epoxy/copper interface after thermal aging