Abstract:We report here a detailed characterization of the surface chemical states and morphology of polyimide (PI) films following modifications by plasma treatment and electroless copper deposition. NH3 and Ar plasma treatments have been successfully used to achieve morphological and chemical modification of the PI surface so that electroless copper plating can occur. The adhesion strength of the electroless copper to the PI surface was measured and correlated with the plasma-induced chemical and physical modifications of the PI surface. The NH3 plasma causes primarily chemical changes to the PI surface through creation of nitrogen moieties (i.e., –N =C< ) on the surface. The Ar plasma treatment brings about mainly physical changes to the surface (i.e., surface roughening). The combined-plasma treatment (Ar plasma followed by NH3 plasma) combines the desirable chemical and physical effects of each treatment, yielding a PI surface with higher roughness for physical anchoring of the copper and surface bonding sites (nitrogen and oxygen sites). During the electroless copper surface activation step with tin chloride and palladium chloride, tin bonds mainly with the oxygen on the surface, whereas palladium reacts with tin chloride as well as with the surface nitrogen. A direct relationship has been observed between surface palladium concentration and the abundance of the –N =C< sites on the surface. This suggests that the nitrogen radicals created during the NH3 plasma are incorporated into the surface and serve as bonding sites for the palladium. In the subsequent electroless Cu deposition, there was a direct correlation between the palladium surface concentration and Cu coverage. The adhesion strength of the electroless copper to the PI correlated well to the surface modifications and plasma treatment conditions. For the first time, a specific bonding configuration on the PI surface is shown to promote adsorption of palladium, which in turn promotes covalent bonding with Cu. The relative importance of surface roughness and chemical bonding on the adhesion strength is discussed.

Copper Metallization on the Surface-Modified Polyimide Films by Electroless Plating Method

Electroless Plating of Copper via a Sn-Free Process on Dielectric SiLK Surface Modified by UV-Induced Graft Copolymerization with 4-Vinylpyridine and 1-Vinylimidazole

Plasma Treatment and Surface Analysis of Polyimide Films for Electroless Copper Buildup Process

Modification of Cu Nanoparticles with A Disulfide for Polyimide Metallization

Electroless Plating of Copper on Fluorinated Polyimide Films Modified by Plasma Graft Copolymerization and UV‐induced Graft Copolymerization with 4‐Vinylpyridine

Direct additive copper plating on polyimide surface with silver ammonia via plasma modification

Photocatalytic Surface Modification of PI Film for Electroless Copper Plating

Effect of Silver Nitrate on Electroless Copper Plating on the Surface of Polyimide Film

Nucleation and growth of low resistivity copper thin films on polyimide substrates by low-temperature atomic layer deposition

Imprinting Of Metal Receptors Into Multilayer Polyelectrolyte Films: Fabrication And Applications In Marine Antifouling

Studies of Polyimide/copper Interface and Its Improvement by a Two‐component Primer

Preparation of Highly Reflective and Conductive Metallized Polyimide Films Through Surface Modification: Processing, Morphology and Properties

Direct Ion Exchange Self‐Metallization: A Novel and Efficient Route for the Preparation of Double‐Surface‐Silvered Polyimide Films

Surface Modification of Copper for Adhesion Promotion by Polybenzimidazole

Fabrication of Polyimide Composite Film with Both Magnetic and Surface Conductive Properties

Copper-Catalyzed Electroless Nickel Coating on Poly(Ethylene Terephthalate) Board for Electromagnetic Application

Improvement of Copper Plating Adhesion on Silane Modified Pet Film by Ultrasonic-Assisted Electroless Deposition

Copper metallization of carbon fiber-reinforced epoxy polymer composites by surface activation and electrodeposition

Adhesion Properties of Electroplating Process Between Polyimide and Metal Layer for Polymer/Metal Hybrid Bonding

Grafting Amino Groups onto Polyimide Films in Flexible Copper-Clad Laminates Using Helicon Plasma

Adhesive properties of deposited Cu films on colorless polyimide using high power impulse magnetron sputtering system