Abstract:We report here a detailed characterization of the surface chemical states and morphology of polyimide (PI) films following modifications by plasma treatment and electroless copper deposition. NH3 and Ar plasma treatments have been successfully used to achieve morphological and chemical modification of the PI surface so that electroless copper plating can occur. The adhesion strength of the electroless copper to the PI surface was measured and correlated with the plasma-induced chemical and physical modifications of the PI surface. The NH3 plasma causes primarily chemical changes to the PI surface through creation of nitrogen moieties (i.e., –N =C< ) on the surface. The Ar plasma treatment brings about mainly physical changes to the surface (i.e., surface roughening). The combined-plasma treatment (Ar plasma followed by NH3 plasma) combines the desirable chemical and physical effects of each treatment, yielding a PI surface with higher roughness for physical anchoring of the copper and surface bonding sites (nitrogen and oxygen sites). During the electroless copper surface activation step with tin chloride and palladium chloride, tin bonds mainly with the oxygen on the surface, whereas palladium reacts with tin chloride as well as with the surface nitrogen. A direct relationship has been observed between surface palladium concentration and the abundance of the –N =C< sites on the surface. This suggests that the nitrogen radicals created during the NH3 plasma are incorporated into the surface and serve as bonding sites for the palladium. In the subsequent electroless Cu deposition, there was a direct correlation between the palladium surface concentration and Cu coverage. The adhesion strength of the electroless copper to the PI correlated well to the surface modifications and plasma treatment conditions. For the first time, a specific bonding configuration on the PI surface is shown to promote adsorption of palladium, which in turn promotes covalent bonding with Cu. The relative importance of surface roughness and chemical bonding on the adhesion strength is discussed.

Adhesion Properties of Electroplating Process Between Polyimide and Metal Layer for Polymer/Metal Hybrid Bonding

Super-high interface adhesion through silver/polyimide heterojunction

Grafting Amino Groups onto Polyimide Films in Flexible Copper-Clad Laminates Using Helicon Plasma

Imprinting Of Metal Receptors Into Multilayer Polyelectrolyte Films: Fabrication And Applications In Marine Antifouling

Study on Aging Effect of Adhesion Strength Between Polyimide Film and Copper Layer

Studies of Polyimide/copper Interface and Its Improvement by a Two‐component Primer

Adhesion improvement of sputtered Cu films on flexible polymer substrates through the design of metal interlayers

Interpenetration Networked Polyimide–Epoxy Copolymer under Kinetic and Thermodynamic Control for Anticorrosion Coating

Mechanism analysis of PI/PEEK interface bonding properties enhanced by atmospheric plasma treatment: Experiment and DFT calculation

Surface Modification of Copper for Adhesion Promotion by Polybenzimidazole

Plasma Treatment and Surface Analysis of Polyimide Films for Electroless Copper Buildup Process

Bio-Inspired Interlocking Structures for Enhancing Flexible Coatings Adhesion

Understanding Electrical Failure of Polyimide-Based Flexible Neural Implants: The Role of Thin Film Adhesion

Enhancing the bond strength of magnetron-sputtered copper layers on polyimide and polyether ether ketone surfaces through surface modification

Study on the interfacial interactions and adhesion behaviors of variouspolymer-metalinterfaces in nano molding

Plasma surface pretreatment to improve interfacial adhesion strengths of sputtered Cu on polyimide film

Interfacial Modification of Polymer/metal Joints by a Two-Component Coupling System of Polybenzimidazole and 2-Mercaptobenzimidazole

Effect Of Piii On The Adhesion Behavior Of Epoxy Molding Compound-Nickel Interface

Adhesive properties of deposited Cu films on colorless polyimide using high power impulse magnetron sputtering system

Properties of Cu Film and Ti/Cu Film on Polyimide Prepared by Ion Beam Techniques

Electroless Plating of Copper on Fluorinated Polyimide Films Modified by Plasma Graft Copolymerization and UV‐induced Graft Copolymerization with 4‐Vinylpyridine