Abstract:High performance engineering thermoplastics modified epoxy resins are novel materials avoiding the usual shortcomings of rubber modification (i.e., reduction of glass transition temperature, yield strength, and elastic modulus), and having improved impact strength and fracture toughness [1, 2]. Although the use of thermoplastic modifier has been important for the improvement of fracture toughness is a mechanical property high performance epoxy resins, there is limited information concerning the interfacial control between thermoplastic modifier and epoxy resins [3]. And in most cases, commercial thermoplastics are directly used as modifiers without effective control of the interface between the dispersed phase and the cured epoxy resin. There are two ways to improve the interfacial adhesion between the dispersed thermoplastics phase and the cured epoxy resin. The first is to chemically modify or functionalize the thermoplastics modifier. The second is to introduce mutual interaction, such as dipole-dipole interaction, hydrogen-bonding etc., into the curing system to improve the compatibility. Recent studies have shown that the interfacial adhesion between thermosets and thermoplastics can be dramatically improved when interdiffusion is possible [4]. Here, we prefer the second way since the development of functional polymers is still limited to the laboratory and it is a high cost process. This paper reports the incorporation effect of a second thermoplastics modifier (PC), on the phase separation behavior and morphology of PEI modified E-51 curing systems by using small angle laser light scattering (SALLS) and scanning electron microscopy (SEM, Hitachi S-570). The samples were made by incorporating various contents of polyetherimide (PEI; General Electric Co., USA) and polycarbonate (PC, based on bisphenonl-A; Idenitsu Kosan Co., Japan) into E-51 (a commercial grade epoxy resin based on diglycidyl ether of bisphenonl-A; Hangzhou Chemical Plant China) by weight. Then cured with 4,4 � diamino-diphenylsulphone (DDS; Chemical agent Co., China).

Interfacial Modification of Polymer/metal Joints by a Two-Component Coupling System of Polybenzimidazole and 2-Mercaptobenzimidazole

Adhesion promotion for epoxy resin/copper and polyimide/copper joints by a two‐component coupling system of poly(4‐vinylimidazole) and cystamine

Adhesion Promotion at High Temperature for Epoxy Resin or Polyimide Onto Metal by a Two‐component Coupling System of Polybenzimidazole and 4‐aminophenyl Disulfide

Surface Modification of Copper for Adhesion Promotion by Polybenzimidazole

Complex-Induced Coupling Effect - Adhesion of Some Polymers to Copper Metal Promoted by Benzimidazole

Enhanced Compatibility and Thermo-Oxidative Stability of Silicone Rubber/Ethylene–Propylene Terpolymer Composites Via in Situ Interface Coupling

Complex-Induced Coupling Effect: Adhesion of Polymers to Metal Promoted by Azole Compound

Interfacial Modification for an Aluminum/epoxy Resin Laminated Composite

Studies of Polyimide/copper Interface and Its Improvement by a Two‐component Primer

The Coupling Mechanism of Benzotriazole Pretreated Copper Metal and Epoxy-Resin

Adhesion Properties of Electroplating Process Between Polyimide and Metal Layer for Polymer/Metal Hybrid Bonding

Enhancing interfacial performance of epoxy resin composites via in-situ nucleophilic addition polymerization modification of carbon fibers with hyperbranched polyimidazole

Studies of copper-catalysed degradation of epoxy coatings and a method for improving the durability of an epoxy/copper interface after thermal aging

The Dynamic Mechanical Analysis of Epoxy–copper Powder Composites Using Azole Compounds As Coupling Agents

Enhancement of Mechanical Properties and Bonding Properties of Flake-Zinc-Powder-Modified Epoxy Resin Composites

Chemically dealloyed Mg–Cu alloy lamina as an interlayer for reinforcing a C/C composite – TC4 alloy vacuum brazed joint

Surface-enhanced Raman Scattering and Cyclic Voltammetry Studies of Synergetic Effects in the Corrosion Inhibition of Copper by Polybenzimidazole and Mercaptobenzimidazole at High Temperature

The Role of Surface Treatment and Coupling Agents for Adhesion between Stainless Steel (SUS) and Polyamide (PA) of Heterojunction Bilayer Composites

Preliminary investigation of a second thermoplastic modifier incorporation effect on the phase behavior and morphology of epoxy/PEI curing systems

A coupling strategy for excellent mechanical properties and enhanced interfacial performance of polyimide/carbon fiber composite with metal-free catalyzed-curing route

Design, Preparation and Characterization of a High-Performance Epoxy Adhesive with Poly (Butylacrylate-block-styrene) Block Copolymer and Zirconia Nano Particles in Aluminum- Aluminum Bonded Joints