Abstract:This work examines Cu(In,Ga)Se2 thin films fabricated by (1) selenization of pre-sputtered Cu-In-Ga and (2) co-evaporation of each constituent. The efficiency disparity between films deposited via these two methods is linked to differences in morphology and microstructure. Atomic force microscopy and scanning electron microscopy show that selenized films have rougher surfaces and poor adhesion to molybdenum back contact. Transmission electron microscopy and electron energy loss spectroscopy revealed multiple voids near the Mo layer in selenized films and a depletion of Na and Se around the voids. Residual stresses in co-evaporated films were found to be ∼1.23 GPa using wafer curvature measurements. Uniaxial compression experiments on 500 nm-diameter nanopillars carved out from co-evaporated films revealed the elastic modulus of 70.4 ± 6.5 GPa. Hertzian contact model applied to nanoindentation data on selenized films revealed the indentation modulus of 68.9 ± 12.4 GPa, which is in agreement with previous reports. This equivalence of the elastic moduli suggests that microstructural differences manifest themselves after the yield point. Typical plastic behavior with two distinct failure modes is observed in the extracted stress-strain results, with the yield strength of 640.9 ± 13.7 MPa for pillars that failed by shearing and 1100.8 ± 77.8 MPa for pillars that failed by shattering.

Preparation and characterization of Cu(In,Ga)Se2 thin films derived by frequency magnetron sputtering

Increasing surface band gap of Cu(In,Ga)Se2 thin films by post depositing an In-Ga-Se thin layer.

Optimization of Fabrication Parameters of CuInSe2 Thin Films by DC-Magnetron Sputtering the Metal Precursor Followed by Selenization

Preparation And Characterization Of Cu(In,Ga)Se-2 Thin Films By Selenization Of Cu0.8ga0.2 And In2se3 Precursor Films

Study of Cu–In–Ga Precursor for Cu(In,Ga)Se_2 Thin Film Prepared by the Two-Stage Process

Influence of Ga Concent of CuInGa Precursor on Stoichiometry of Cu(In1 - xGax) Se2 Photon Absorption Films

Growth of High-Quality Cuinse2 Polycrystalline Films by Magnetron Sputtering and Vacuum Selenisation

Research on CuInS2 Thin Films Prepared by One-step Electrodeposition

Structural and optical properties of CuInS2 thin films prepared by magnetron sputtering and sulfurization heat treatment

PROCESS AND PERFORMANCE OF CHALCOPYRITE CIGSe ABSORBERS FABRICATED BY MAGNETRON SPUTTERING

Study on How the Content of Selenium in the Precursors Influences the Properties of CuInSe2 Thin Films

Preparation and properties of compositionally tunable Cu3Sb(Sx,Se1-x)4 thin films

Segregation of Ga in CuInGaSe2 Films Grown by Magnetron Sputtering and Selenization

Strength, stiffness, and microstructure of Cu(In,Ga)Se2 thin films deposited via sputtering and co-evaporation

Preparation and characterization of CuInSe2 thin films derived by electrodeposition process for solar cells

Effects of different sulfurization conditions on the characterization of CuIn(S x Se 1− x ) 2 thin films

Fabrication and characterization of CuInS 2 films by chemical bath deposition in acid conditions

Preparation and characterization of Cu2ZnSnSe4 thin films by selenization of electrodeposited metal precursors

The effects of sputtering power on optical and electrical properties of copper selenide thin films deposited by magnetron sputtering

Effects of Cu-In Precursor Film Phase Structure on CuInSe2 Film Properties

Effects of sputtering power on compositions and microstructures of precursor films for cigs absorber