Abstract:In the present work, (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 were produced by common casting and hot-forging technology utilizing the SHS reactions between titanium and B4C, C powder. The microstructures of composites were examined using optical microscopy (OM) and transmission electron microscopy (TEM). The X-ray diffraction (XRD) was used to identify the phases that were present in the composites. There are three phases — TiB, TiC and titanium matrix alloy. TiB grows in short-fiber shape, whereas TiC grows in dendritic, equiaxed or near-equiaxed shape. TiB whiskers were made to align the longitudinal direction and TiC dendritic was broken up after hot-forging. The reinforcements are distributed uniformly in matrix alloy. The interfaces between reinforcements and titanium matrix alloy are very clean. The tensile strength (yield strength and ultimate tensile strength) and the Young's modulus improve with the addition of TiB whiskers and TiC particles although some reduction in ductility is observed. (TiBw+TiCp)/Ti6242 composites with TiB:TiC=4:1 will fracture on a lower level of applied stain due to deformation restraint of TiB whiskers on titanium matrix alloy. The (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 show higher tensile strength and ductility. The addition of graphite not only improves the tensile strength and the Young's modulus but also increases the ductility. The improved Young's moduli and increased tensile strengths of the composites are explained using shear lag and rule-of mixtures theories. The Young's moduli of the composites were found in good agreement with that calculated from Tsai–Halpin equation applied for discontinuous-reinforced composites.

Dense TiC-Al2O3 composites fabricated by SHS

DENSE TiC-Al2O3-Fe CERMET FABRICATED BY SHS

In situ synthesis and mechanical properties of bulk Ti3SiC2/TiC composites by SHS/PHIP

Microstructures of TiC-Al2O3-Fe composites prepared by SHS/PHIP

Rapid Synthesis of Bulk Ti2alc by Self-Propagating High Temperature Combustion Synthesis with A Pseudo-Hot Isostatic Pressing Process

Research on TiC-Ni cermets by SHS and pseudo heat isostatic pressing

Investigation on NiAl–TiC–Al2O3 Composite Prepared by Self-Propagation High Temperature Synthesis with Hot Extrusion

Self-propagating high temperature combustion synthesis of TiB/Ti composites

PROPERTIES OF TiC-Al2O3/Fe COMPOSITES PREPARED BY SHS/PHIP

Synthesis and Properties of AlN-SiC-TiB2 Ceramics by SHS-HIP

Self-propagating high-temperature synthesis of TiC-TiB2 multiphase ceramics

Growth Morphology and Microstructural Characterization of Nonstoichiometric Ti2alc Bulk Synthesized by Self-Propagating High Temperature Combustion Synthesis with Pseudo Hot Isostatic Pressing

Fabrication of AlN-SiC-TiB2 Ceramics by Self-Propagating High Temperature Synthesis and Hot Isostatic Pressing

Effects of Forming Conditions and TiC–TiB 2 Contents on the Microstructures of Self-Propagating High-Temperature Synthesized NiAl–TiC–TiB 2 Composites

Al3Ti/Al composites prepared by SHS

Microstructure and tensile properties of in situ synthesized (TiBw + TiCp)/Ti6242 composites

Influence Of Heat Treatment On The Microstructure And Properties Of Ti2alc By Shs/Phip

Preparation of Al–TiC Composites by Self-Propagating High-Temperature Synthesis

Microstructure and Tensile Properties of in Situ (tib+tic)/ti6242 (tib:Tic=1:1) Composites Prepared by Common Casting Technique

COMBUSTION SYNTHFSIS AND DENSIFICATION BY GAS HOT ISOSTATIC PRESSURE OF AIN- TiB2 CERAMIC WITHOUT ENVELOPE

Microstructure and formation mechanism of TiC-30Fe cermet fabricated by SHS