Abstract:Semi-solid thixoforming processes rely on a material microstructure made of globular solid grains more or less connected to each other, thus developing a solid skeleton deforming into a liquid phase. During processing, the material structure changes with the processing history due to the agglomeration of the particles and the breaking of the grains bonds. This particular evolutive microstructure makes semi-solid materials behave as solids at rest and as liquids during shearing, which causes a decrease of the viscosity and of the resistance to deformation while shearing. Thixoforming of aluminum and magnesium alloys is state of the art and a growing number of serial production lines are in operation all over the world. But there are only few applications of semi-solid processing of higher melting point alloys such as steel. This can partly be attributed to the high forming temperature combined with the intense high temperature corrosion that requires new technical solutions. However the semi-solid forming of steels reveals high potential to reduce material as well as energy consumption compared to conventional process technologies, such as casting and forging. Simulation techniques exhibit a great potential to acquire a good understanding of the semi-solid material process. Therefore, this work deals with the development of an appropriate constitutive model for semi-solid thixoforming of steel. The constitutive law should be able to simulate the complex rheology of semi-solid materials, under both steady-state and transient conditions. For example, the peak of viscosity at start of a fast loading should be reproduced. The use of a nite yield stress is appropriate because a vertical billet does not collapse under its own weight unless the liquid fraction is too high. Furthermore, this choice along with a non-rigid solid formalism allows predicting the residual stresses after cooling down to room temperature. Several one-phase material modeling have been proposed and are compared. Thermomechanical modeling using a thermo-elasto-viscoplastic constitutive law has been developed. The basic idea is to extend the classical isotropic hardening and viscosity laws to the non solid state by considering two non-dimensional internal parameters. The rst internal parameter is the liquid fraction and depends on the temperature only. The second one is a structural parameter that characterizes the degree of structural build up in the microstructure. Those internal parameters can depend on each other. The internal parameters act on the the viscosity law and on the yield surface evolution law. Di erent formulations of viscosity and hardening laws have been proposed and are compared to each other. In all cases, the semi-solid state is treated as a particular case, and the constitutive modeling remains valid over the whole range of temperature, starting from room temperature to above the liquidus. These models are tested and illustrated by mean of several representative numerical applications.

Research on the constitutive relationship of semi-solid ZL201 alloy

Viscosity Estimation of Semi-Solid Alloys Based on Thermal Simulation Compression Tests

Numerical Analysis of Semi-Solid Die-Casting Automobile Part Based on the Thermo-Visco-Plastic Constitutive Relation

Numerical Simulation of Semi-Solid Die-Casting Process of Automobile Aluminum Alloy Part

Constitutive relationship of semi-solid ZL101 alloy in thixoforming

Die Casting Semi-Solid ZL101 Alloy Prepared by Inclined Slope Cooling-Transferring Method and its Properties

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Experimental research on fluidity of semi-solid alloy ZL101 mircoextrusion

Development of a Semi-solid Zn-Al Alloy Filler Metal with Globular Grains

Relationship of Compositions, Phase Constituents and Solidification Paths of Casting Mg-Al-Zn Alloys

Numerical Simulation and Experimental Study on Semi-solid Forming Process of 319s Aluminum Alloy Test Bar

The Effect of Initial Microstructure of A356 Alloys on the Mechanical Behavior in the Semisolid State

Study on a Semi-Solid Rheo-Diecasting Process With AZ91D Alloy Slurry

Experiment and Numerical Simulation of Microstructure of ZL114A Alloy in Low Pressure Casting

Rheological modeling and simulation of semi-solid slurry based on experimental study

Experimental study on semi-solid micro-compression of ZL101 alloy

Multiphase modelling of the transient flow for Sn-15Pb and 357.0 alloys in semi-solid die casting process

Microstructure Evolution During Remelting of High Solid Fraction ZL101 Alloy

Constitutive Behavior Predictions of Mushy Zone During Solidification by Phase Field Model and Coupled Eulerian–Lagrangian Method

Semi-solid constitutive modeling for the numerical simulation of thixoforming processes.

Microstructure Simulation of Zl114a Alloy During Low Pressure Die Casting Process