Abstract:The 2195 Al-Li alloy, as one of the representative third-generation Al-Li alloys, has extensive applications in lightweight aerospace structures. In this paper, the anisotropy in mechanical properties and microstructure evolution of 2195 Al-Li alloy sheets were investigated under a strain rate of 0.01, 0.1, 1 s-1 and a temperature of 440 and 500 °C. Experimental results showed that the hot tensile properties of the 2195 Al-Li alloy sheet exhibited a strong dependence on loading directions. The peak stress (PS) and elongation (EL) along the rolling direction (RD) were larger than the transverse direction (TD). For the tests carried out at 440 °C-1 s-1, the PS values of the sheets stretched along the RD and TD are 142.9 MPa and 110.2 MPa, respectively. And, most of the PS anisotropy values are larger than 15%. The anisotropy in EL is less significant than in PS. All the differences are about 10%. Moreover, dimples in the samples stretched along RD were more and deeper than those along TD at 440 °C. The fracture morphology along RD and TD were similar, and both were cleavage fractures at 500 °C. Particularly, the fractions of high angle grain boundaries (HAGBs) along TD were all about 5% larger than those of RD. And, there were more small-sized continuous dynamic recrystallization (CDRX) grains inside the initial grains and discontinuous dynamic recrystallization (DDRX) grains featured with the local bulge of grain boundaries along TD. This was due to the smaller average Schmid factor and the vertical EL trend of the initial grains when the samples were stretched along TD. A model of grain evolution during the dynamic recrystallization (DRX) along RD and TD was proposed based on EBSD results. The Schmid factor and banded structure had a more prominent effect on the hot ductility of the 2195 Al-Li alloy compared with the degree of DRX, thus presenting a higher EL and better hot ductility along RD.

The Influences of the Microstructure Morphology of A356 Alloy on Its Rheological Behavior in the Semi-Solid State

Modeling Microstructure Evolution in Shape Memory Alloy Rods Via Legendre Wavelets Collocation Method

Rheological Behavior of Semisolid A356 Alloy with Different Morphology of Primary Α Phases

Static Shearing Rheological Behavior of Semi-solid A356 Alloy

On the Size Effects in Micro/meso Semisolid Extrusion–forging of A356 Aluminum Alloy

Rheologic Properties of Aluminum Alloy A356 Bille ts Produced by Semisolid Continuous Casting Process

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Microstructural Features of Semi-Solid A357 Alloy Slurry Under High-Shear Melt Processing

Rheological Behavior of the A356 Alloy in the Semisolid State at Low Shear Rates

New technique for preparing A356 alloy semisolid slurry and its rheo-diecast microstructure and properties

Comparison of Rheological Models to Simulate Die Filling Process of A356 Semisolid Alloy

Development of Rheometer for Semi-Solid High-Melting Point Alloys

The solidification characteristics of 6061 and A356 aluminum alloys and their ceramic particle-reinforced composites

Influence of Process Papameters by Vibrational Cooling-Shearing Slope on Microstructures of Semi-Solid ZAlSi9Mg Alloy

Development of Microstructure of Semi-Solid A356 Alloy by Alternating Electromagnetic Stirring

Microstructural length scale manipulation via solidification and its influence on mechanical behavior in a high-strength intermetallic-based eutectic alloy

Enhanced comprehensive performance via alloying and rheo-diecasting in a semi-solid Al–Si–Fe–Mg–Cu–Sr alloy

Dependence of microstructure and mechanical properties on solidification condition of directionally solidified Zn-55Al-1.6Si alloys

Effects of Solid–Liquid Mixing on Microstructure of Semi-Solid A356 Aluminum Alloy

Microstructural Features and Wear Characteristics of Semi-Solid Processed A356 Aluminum Alloy

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation