Abstract:Semisolid metal (SSM) processing has become an important industry forming process. Now, the traditional casting or forging alloys cannot show all advantages of semisolid metal processing. Especially, the magnesium alloys currently used in SSM processing are restricted to a few commercial alloys such as AZ91, AM50 and AM60. Therefore, in order to vary semisolid alloys, a new Mg–10Al–4Zn alloy is designed on the basis of conventional AZ91D alloys in this paper. The microstructure evolution and rheological parameter of semisolid Mg–10Al–4Zn alloy was investigated. The microstructure of casting consists of α-Mg and β-Mg17Al12. After compressed by a ratio of 40% in height at the temperature of 210°C, the microstructure of Mg–10Al–4Zn alloy changed from developed dendrites to near-equiaxed grains, and all the dendrites oriented in the same orientation. Whereafter, fine recrystallization grains were formed by the release of the stored fault energy induced by deformation at the elevated temperature. The Mg17Al12 phase containing zincum firstly melted between boundaries of the primary grains and then penetrated into recrystallization grain boundaries, which resulted in the separation of the fine primary grains suspending in liquid phase. The partially melting was discussed through analyzing the phase transformations. In addition, the research on rheological parameters such as solid fraction, the particle size, the spherical degree, and the distribution of liquid phase showed that the Mg–10Al–4Zn alloy had a good semisolid performance.

Influence of Process Papameters by Vibrational Cooling-Shearing Slope on Microstructures of Semi-Solid ZAlSi9Mg Alloy

Formation of Non-Dendritic Microstructure of Semi-Solid Aluminum Alloy under Vibration

Efficient fabrication of semisolid nondendritic Al alloy slurry with high quality

Development of Non-Dendritic Microstructure of Aluminum Alloy in Semi-Solid State under Ultrasonic Vibration

Microstructure, Properties, and Numerical Simulation of Semi-Solid Aluminum Alloy under Planetary Stirring Process

Microstructural Evolution of Mg9AlZnY Alloy with Vibration in Lost Foam Casting During Semi-Solid Isothermal Heat Treatment

Improved Mechanical Performances of Dynamically Solidified Mg97.7Y1.4Al0.9 Alloy by Three Dimensional Ultrasounds

Effect of cooling condition on microstructure of semi-solid AZ91 slurry produced via ultrasonic vibration process

Effects of Vibration and Grain Refiner on Microstructure of Semisolid Slurry of Hypoeutectic Al-Si Alloy

Ultrasonic Solidification Mechanism and Optimized Application Performances of Ternary Mg71.5Zn26.1Y2.4 Alloy

Preparation of Al Alloy ZL101 Semi-solid Slurry by Ultrasonic Vibration Method

Study on preparing al alloy ZL101 semi-solid slurry by mechanical vibration method

Mechanism of Alloy Microstructure Globularisation During Cooling Slope Process

Preparation of semisolid A356 alloy by a cooling slope processing

Effects of Vibrating the Cooling Pipe on the Solidification Microstructure of A357 Alloy

Research on Preparing Semi-solid Slurry of Aluminum Alloy by Mechanical Vibration

Study on the microstructure evolution and rheological parameter of semisolid Mg–10Al–4Zn alloys

Formation of Spheroidal Microstructure in Semi-solid State of Al-4.8Si-2.8Cu-0.5Mg Aluminium Alloy

In-situ observation of SSM microstructure formation during cooling slope casting of an NH4Cl-H2O alloy with vibrating the slope

Technological Optimization of Preparing ZL101 Aluminum Alloy Semi-Solid Slurry by Mechanical Vibration

Effects of Vibrating the Chilling Path on the Solidifying Microstructure of Sn-15%Pb Alloy