Abstract:The solidification behaviours and microstructural characteristics of both ZA27/SiCp composites and monolithic ZA27 alloy were studied by using differential scanning calorimetry, scanning electron microscopy, transmission electron microscopy, electron probe microanalysis, and X-ray diffraction, It was found that there were differences in the transformation temperature and volume fraction of the phases, although the solidification process was almost identical for the composite and the monolithic alloy. The incorporation of SiC particles in the ZA27 alloy led to slight refinement of primary grains and reduced volume fraction of eutectic-like phase. The SiC particles obstructed Zn diffusion in the residual melt during the formation of proeutectic beta phase, but promoted Zn diffusion from alpha (Al) to eta (Zn) phase during eutectoid transformation. During solidification, Cu was mainly segregated in the final solidification regions; Mg was present not only in the matrix but also on SiC particles; and oxide inclusions were mainly distributed around SiC particles, The matrix microstructure for both materials mainly consisted of primary cores of Al rich alpha + eta eutectoid; beta' phase resulting from the eutectoid transformation of the proeutectic beta phase; and Zn rich alpha + eta eutectoid resulting from the eutectoid transformation of the eutectic-like phase. The SiC particles were mainly distributed around the primary grains, Several new phases based on the Al-Zn-Mg-Cu system and interfacial reaction products, including Al21Fe3Si, Cu5Zn8, Mg6Cu3Al7, MgAl2O4, and amorphous oxide inclusions, were identified in the final solidification regions. The nucleation of both primary alpha phase and eutectic-like alpha + eta phase at the surface of SIC particles and their crystallographic orientation relationships were investigated theoretically and experimentally. No distinct crystallographic orientation relationship between the matrix and SiC has been identified, although the mismatch between (0001)(SiC) and (111)(alpha) was calculated to be as small as 7.6%.

Effect of compression ratio on microstructure evolution of Mg–10%Al–1%Zn–1%Si alloy prepared by SIMA process

Effect of Mg on Nucleation Process of Recrystallization in Al–Mg–Si/SiCp Composite

Microstructural evolution of Mg-10Gd-3Y-1Zn-0.4Zr (wt%) alloy prepared by strain-induced melt activation process

Structure Shape and Forming Mechanism of Semi-Solid Material of AZ91D Magnesium Alloy by SIMA Process

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Microstructures of Semi-Solid AZ91D Magnesium Alloys Billets Prepared by Cold Rolling SIMA Method

Compound Fabrication Technology of Semi-Solid Billet of Al-Si Alloy Based on SIMA Method

The effect of Cu–8%P master alloy, SIMA process, thixoforming, and heat treatment on the microstructure and mechanical properties of Al–20%Mg 2 Si composite

Microstructure, Hot Deformation Behavior, and Textural Evolution of Mg–3wt%Zn–1wt%Ca–0.5wt%Sr Alloy

Effect of cross-sectional reduction ratio on microstructure evolution of semi-solid 7075 aluminum alloy prepared by RFSIMA process

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

The multi-scale Si-containing phases-assisted improvement in the microstructure and mechanical properties of Al–Mg-xSi-Cu-Zn alloys

Development of Spherical Eutectic Si Particles through M-SIMA Process and Its Effects on the Tensile Properties of Al-7Si-0.05Sr Alloy

Microstructure evolution of AZ80 magnesium alloy in semi-solid compression by molecular dynamics simulation

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Solidification and microstructure of ZA27/SiCp composite fabricated by mechanical-electromagnetic combination stirring process

Relationship between Microstructure Evolution and Tensile Properties of AlSi10Mg Alloys with Varying Mg Content and Solidification Cooling Rates

Microstructures and mechanical properties of Si and Zr modified Al–Zn–Mg–Cu alloy-A comparison between selective laser melting and spark plasma sintering

Microstructure of semi-solid AZ91D magnesium alloy after hot compression

Influence of Si Addition on the Microstructure and Mechanical Behaviour of Mg-5Sn-3Zn-1Mn Alloy

Effect of Zn/Mg ratio on the microstructure and mechanical properties of as-cast Al–Zn–Mg–Cu alloys and the phase transformation during homogenization