Abstract:In this study, Al-20 wt% Mg 2 Si composites were prepared using an in situ endogenous process method. Various amounts of Sc were added to the composites, and a heat treatment process was employed to optimize the microstructures of the materials and enhance the overall properties of the composites. The study results indicate that the addition of Sc has a significant positive effect on both the microstructure and mechanical properties of Al-20 wt% Mg 2 Si composites. The inclusion of Sc leads to a more regular and uniformly distributed morphology of the primary Mg 2 Si phase, accompanied by a significant reduction in grain size. Particularly, when the Sc content is 0.3 wt%, the composite exhibits the most notable grain refinement effect, resulting in the best mechanical performance. The tensile strength reaches 152.7 MPa, the hardness measures 92.9 HV and the elongation is 2.82%. Through the heat treatment process, the morphology and distribution of the initial Mg 2 Si phase in the composites were optimized, resulting in significant improvements in both the morphology and distribution of the initial Mg 2 Si phase and the eutectic structure. Consequently, the tensile strength increased to 204.3 MPa, the hardness reached 117.8 HV, and the elongation improved to 3.72%. Finite element simulation was employed to model the tensile behavior of real microstructures of Al-20 wt% Mg 2 Si-0.3 wt% Sc composite in both as-cast and heat-treated conditions. The simulation results demonstrate good agreement with experiment. The fracture modes observed in both cases involve interfacial debonding and intergranular fracture. The simulation effectively showed the deformation process and stress distribution during tensile fracture. Moreover, the heat-treated model exhibits a higher load on the particles compared to the as-cast state. This finding provides evidence that the overall properties of Al-Mg 2 Si composites are enhanced following the heat treatment process.

The effect of Cu–8%P master alloy, SIMA process, thixoforming, and heat treatment on the microstructure and mechanical properties of Al–20%Mg 2 Si composite

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Effect of beryllium addition and heat treatment on the microstructure and mechanical properties of the 15%Mg2Si/Al-8Si composite

Effect of cooling rates and heat treatment time on Si phase of AlSi10Mg alloy manufactured by selective laser melting: Microstructure evolution and strengthening mechanism

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Effect of mechanical conditions on the microstructures and mechanical properties of thixoformed Al-Cu-Si-Mg alloy

Effect of ageing and thermal exposure on microstructure and mechanical properties of a HPDC Al–Si–Cu–Mg alloy

The Effect of Heat Treatment on the Mechanical Properties and Oxidation Resistance of AlSi10Mg Alloy

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Microstructure and properties of a HIP manufactured SiC p reinforced high alloyed Al–Zn–Mg–Cu–Zr–Ti aluminum matrix composite

Effect of Remelting Temperature and Soaking Time on Microstructure and Mechanical Properties of the Thixoformed Part of Nano-Sized SiCp/7075 Composite

Effects of Yttrium and Heat Treatment on the Microstructure and Tensile Properties of Al–7.5Si–0.5Mg Alloy

Effect of Sc Addition and Heat Treatment on the Fracture Behavior of Al-20%Mg2Si Composites: Experiments and Finite Element Simulations

The Influence of SiC–Al2O3 Reinforcements on the Deformation and Fracture Mechanism of Thixomolded Mg-based Composite

Mechanical and Tribological Characterization of Al-Mg2Si Composites after Yttrium Addition and Heat Treatment

Evaluation of Tensile Properties and Formability of Al 6061 Alloy Processed by Various Semi-solid Techniques

Effects of Heat Treatment on Microstructure and Mechanical Properties of AlSi10Mg Fabricated by Selective Laser Melting Process

Effect of heat treatments on microstructure and mechanical properties of sand cast Al–2Li–2Cu–0.5Mg–0.2Sc–0.2Zr alloy

Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Enhanced Microstructure Homogeneity and Mechanical Properties of AZ31–Si Composite by Cyclic Closed-Die Forging

Microstructure and mechanical properties of an in-situ TiB2 particle reinforced AlSi10Mg composite additive manufactured by selective electron beam melting