Abstract:High strength-elongation synergy and its dependence on microstructure are the eternal themes of metallic materials including Ti alloys. In this study, the relationship between the microstructure evolution and mechanical properties of the Ti-25Zr-4Al-1.5Mn (TZAM, wt. %) near-α Ti alloy was systematically investigated after hot rolling at temperatures ranging in the whole solid solution region. The content of primary α phase decreased gradually with the increasing of rolling temperature. An excellent comprehensive mechanical properties with a yield strength of 1055±10 MPa and a total elongation of 23.6±0.6% were obtained for the specimen after rolling at 750 °C (single α phase temperature region). This great strength-elongation synergy is mainly due to the synthetic action of substructure strengthening, dislocation strengthening, basal random heterogeneity (BRH) texture, and suitable content of β phase. The α" martensitic phase was formed after rolling at temperatures of 800 and 850 °C (α + β two-phase temperature region), resulting in a significant decrease in yield strength. However, remarkable work hardening with a rate of approximately 10 GPa occurred in both specimens. The whole evolution process of primary α grains, namely dynamic recovery and recrystallization during hot-rolled is deeply discussed. When the rolling temperature increased to 900 °C (single β phase temperature region), the dominated acicular α´ martensitic phase with high dislocation density resulted in an ultra-high strength (1264±12 and 1488±11 MPa for yield and tensile strength respectively) at the expense of plasticity. These findings revealed the microstructure evolution and its relationship to the mechanical properties of a TiZr-based alloy after the thermomechanical processing and helped to understand deeply the theory of metallic strengthening and elongation.

Evaluation of Tensile Properties and Formability of Al 6061 Alloy Processed by Various Semi-solid Techniques

The effect of Cu–8%P master alloy, SIMA process, thixoforming, and heat treatment on the microstructure and mechanical properties of Al–20%Mg 2 Si composite

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Microstructural Features and Wear Characteristics of Semi-Solid Processed A356 Aluminum Alloy

Mechanical properties of rapidly solidified Al-Ti alloys after thermal exposure

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Preparation of Mg-Al Series Magnesium Alloy Semi-solid Billets and its Thixo-extrusion Forming

Microstructure and Texture Evolution of 2A12 Aluminum Alloy Semi-Solid Billet Prepared by SIMA Process

Effect of mechanical conditions on the microstructures and mechanical properties of thixoformed Al-Cu-Si-Mg alloy

Microstructure Evolution of AZ91D Magnesium Alloy Semi-solid Billets Prepared by a New SIMA Method

Microstructural Characterization and Mechanical Properties of 6061 Aluminum Alloy Processed with Short-Time Solid Solution and Aging Treatment

Microstructure and high temperature tensile properties of Al–Si–Cu–Mn–Fe alloys prepared by semi-solid thixoforming

Compound Fabrication Technology of Semi-Solid Billet of Al-Si Alloy Based on SIMA Method

Microstructure Evolution and Tensile Properties of In Situ TiB2(p)/Al-Cu Composite Processed by Modified Strain-Induced Melt Activation Method with Equal Channel Angular Pressing Pre-deformation

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

Microstructure and mechanical properties of AZ61 magnesium alloy parts achieved by thixo-extruding semisolid billets prepared by new SIMA

The influence of post-annealing and ultrasonic vibration on the formability of multilayered Al5052/MgAZ31B composite

Effect of Heating Process on Semi-solid Microstructure of Cold Rolled 6061 Aluminum Alloy

Microstructure evolution and tensile mechanical properties of thixoformed high performance Al-Zn-Mg-Cu alloy

Formation of Spheroidal Microstructure in Semi-solid State of Al-4.8Si-2.8Cu-0.5Mg Aluminium Alloy

An investigation on semi-solid forming of A360 aluminium alloy by mechanical stirring