Abstract:Microstructure evolution and fracture behavior of Mg-9.5Gd-0.9Zn-0.5Zr alloy subjected to different heat treatments were systematically investigated using SEM and TEM as well as tensile testing. It was found that the microstructure of the as-cast alloy consisted of α-Mg matrix, net-like eutectic compounds (α-Mg + Mg3 (Gd, Zn)), cubic GdH2 phases and lamellar 14H LPSO phases. After solution treated at 515 °C for 24 h, two different cooling processes were used to elucidate the effect of cooling rates on the precipitation microstructure. With a hot water quenching, those secondary phases were completely dissolved. Instead, grey-like patches were observed within the α-Mg matrix, which were proposed to be rod-like Zn2Zr3 phases around the α-Zr particle. In contrast, with a furnace cooling, the formation of 14H LPSO and several cubic Mg3 (Gd, Zn) phases was observed. Furthermore, after hot water quenching, the subsequent ageing treatment parameters were also optimized to be 225 °C for 48 h. In the peak-aged condition, a denser and uniform distribution of basal precipitates γ″ and several basal precipitates γ′ together with Zn2Zr3 and ZnZr2 phases were observed. The samples after the solution treatment (for both hot water quenching and furnace cooling) showed a much higher ductility than the as-cast alloy, while the tensile yield strength (TYS) and ultimate tensile strength (UTS) remained unchanged. After the peak-ageing, a significant increase in the TYS and UTS but a great loss in ductility was observed. In the as-cast alloy, the initiation of microcracks occurred from the net-like eutectic compounds, which was believed to be one of the most important reasons for the tensile fracture, and showed a co-existence of intergranular and transgranular fracture behavior. After the solution treatment, with a hot water quenching, the fracture can be mainly related with failures along contraction twins, and then showed a transgranular fracture behavior. While, with a furnace cooling, due to the presence of the kinked 14H LPSO phases, the fracture was caused by the broken of 14H LPSO phases, and then lead to a transgranular fracture. The peak-aged alloy exhibited a brittle intergranular fracture, which can be related with failures along soft precipitation free zones (PFZs).

Microstructure and high temperature tensile properties of Al–Si–Cu–Mn–Fe alloys prepared by semi-solid thixoforming

Microstructure evolution and tensile mechanical properties of thixoformed high performance Al-Zn-Mg-Cu alloy

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Microstructure and Mechanical Properties at Elevated Temperature of Powder Metallurgy Al-Zn-Mg-Cu Alloy Subjected to Hot Extrusion

High Temperature Tensile Property and Fracture Behavior of Directionally Solidified Fe-Al-Ta Eutectic Composites

Effect of ageing and thermal exposure on microstructure and mechanical properties of a HPDC Al–Si–Cu–Mg alloy

Influence of thermal exposure on the microstructure evolution and mechanical behaviors of an Al-Cu-Li alloy

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Microstructural Evolution, Precipitation Behavior, and Mechanical Property Response of Cast Al–Li–Cu–Cd–Mn–Zr–Ti Alloy

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Microstructure and mechanical properties of thixoformed GH4037 parts before and after heat treatment

Comparison of the semisolid squeeze casting and gravity casting process on the precipitation behavior and mechanical properties of the Al-Si-Cu-Mg alloy

Effect of Casting Process and Thermal Exposure on Microstructure and Mechanical Properties of Al-Si-Cu-Ni Alloy

Microstructural Evolution and Tensile Properties of Al-Si Piston Alloys during Long-Term Thermal Exposure

Microstructural evolution and mechanical properties of the rapidly-solidified and hot-extruded 2196 Al-Li alloy

Effects of solution temperature on microstructure and mechanical properties of Al-Si-Mg aluminum alloy fabricated by wire-arc additive manufacturing

Microstructural evolution and mechanical properties of an ultrahigh-strength Al−Zn−Mg−Cu alloy via powder metallurgy and hot extrusion

Correlation of Solidification Microstructure Refining Scale, Mg Composition and Heat Treatment Conditions with Mechanical Properties in Al-7Si-Mg Cast Aluminum Alloys

Unsteady-State Horizontal Solidification of an Al–Si–Cu–Fe Alloy: Relationship Between Thermal Parameters and Microstructure with Mechanical Properties/Fracture Feature

High Temperature Tensile Deformation Behavior of New Heat Resistant Aluminum Alloy

Microstructure evolution and fracture behavior of Mg-9.5Gd-0.9Zn-0.5Zr alloy subjected to different heat treatments