Abstract:The high temperature compressive characteristics of relatively light weight AlCoCrFeNi HEA were investigated via compression tests in a wide deformation temperature (T) range of 1073–1373 K and strain rate (ε˙) range of 10−3–1 s−1. Hot deformation led to the phase constitution transformation from the disorder BCC (A2) + order BCC (B2) at the room temperature to FCC + A2+ B2 +σ at 1073 K and 1173 K, and then to FCC + A2+B2 phase at 1273 K and 1373 K. The kinetic analysis was performed based on the flow stress data by using the hyperbolic sine law constitutive models with a higher the correlation coefficient (R2). Using combination of kinetics analysis and microstructure evolution results, it can be concluded that there was a gradual transformation of the dominant deformation mechanism from the symbiosis effects of grain boundary sliding (GBS) in fine grains and local dislocation gliding in coarse grains at 1073 K to the dislocation climbing mechanisms at 1373 K. The flow stress decreased with the decreasing strain rate and/or increasing true strain, as well as the deformation temperature. At 1073 K and 1173 K, the flow softening was primarily associated with the GBS of ultrafine dynamic recrystallization (DRX) grains in the local phase transformation regions, as well as the dynamic precipitation of FCC phases. While, the softening effect was primarily controlled by the dynamic precipitation of FCC phases and dynamic recovery (DRV) at 1273 K. When the deformation temperature rose to 1373 K, the main softening mechanisms were the continuous DRX (CDRX) and DRV, as well as the coarsening and dissolution of A2 phases Moreover, the clear serration behaviors at 1373 K/1s−1 and 1373 K/10−3s−1 were induced by the interaction effect between the dislocation and cluster.

High Temperature Tensile Deformation Behavior of New Heat Resistant Aluminum Alloy

High-temperature, low-cycle fatigue behavior of an Al-Mg-Si based heat-resistant aluminum alloy

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

High-Temperature Mechanical Behavior of Cobalt-Free FeMnCrNi(Al) High-Entropy Alloys

Effects of Al content on microstructures and high-temperature tensile properties of two newly designed CoNi-base superalloys

The Microstructure Evolution and Dynamic Recrystallization Mechanism of Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr Alloys during High-Temperature Deformation

High temperature deformation mechanism and microstructural evolution of relatively lightweight AlCoCrFeNi high entropy alloy

The strengthening role of micro-sized phases and nano-precipitates in Al–Mg 2 Si–Cu(–Ni) alloys at 25 °C and 350 °C

High-Temperature Tensile Strength of Al10Co25Cr8Fe15Ni36Ti6 Compositionally Complex Alloy (High-Entropy Alloy)

L1 2 nanoparticle-strengthened CoNi-based superalloy with ultrahigh yield stress developed using CALPHAD method

Microstructure and strength of a novel heat-resistant aluminum alloy strengthened by T-Al6Mg11Zn11 phase at elevated temperatures

Tensile Properties of a Heat-Resistant Aluminium Alloy Strengthened by T-Al6Mg11Zn11 Intermetallic Phase

Plastic Deformation Behaviors and Mechanical Properties of Advanced Single Crystalline CoNi-base Superalloys

The Hot Tensile Properties, Fracture Features, and Microstructure Evolution of As-Cast 7005 Aluminum Alloy

The Temperature Dependence of High-Temperature Strength and Deformation Mechanism in a Single Crystal CoNi-base Superalloy

Effects of Low Nickel Content on Microstructure and High-Temperature Mechanical Properties of Al-7Si-1.5Cu-0.4Mg Aluminum Alloy

Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys

Hot deformation behavior and workability of a Ni–Co based superalloy

Study of the high-temperature mechanical properties of Al-6061/NiTi reinforced metal matrix composites