Abstract:This study investigates the microstructural behavior of laboratory-produced Al–Mg–Si(X)–Mn aluminum alloys, focusing on the influence of varying Si content during biaxial hot tensile testing. Alloys with Si contents of 0.7%, 0.9%, and 1.3% were subjected to biaxial deformation at temperatures of 200 °C, 300 °C, and 400 °C. Using digital image correlation analysis, the impact of Si content on microstructural evolution under biaxial tensile loading was analyzed. Force–displacement analysis revealed a consistent inverse relationship between temperature and the maximum force required to initiate strain. At the temperature of 200 °C, the Al–Mg–Si(1.3)–Mn alloy required a maximum force of 1500 N, while at the temperature of 400 °C this force decreased to 900 N. The degree of anisotropy varied, with higher Si alloys exhibiting increased resistance to deformation in the transverse direction. In particular, the Al–Mg–Si(1.3)–Mn alloy showed pronounced strain anisotropy, with large major true strain φ 1 values reaching up to 0.32 at 400 °C, compared to 0.26 at 300 °C and 0.2 at 200 °C. Microstructural analysis using electron backscatter diffraction (EBSD) and energy dispersive X-ray spectrometry (EDS) showed minimal changes at low temperatures, while increased dislocation density and grain boundary distortion were observed at elevated temperatures. The β-Mg 2 Si precipitates, influenced by Si content and temperature, significantly affected the mechanical properties. In the Al–Mg–Si(0.7)–Mn alloy, precipitates were predominantly 1–3 μm in diameter, whereas in the Al–Mg–Si(1.3)–Mn alloy, precipitates grew to 4–8 μm at higher Si content. These findings provide critical insights into the mechanical response and deformation mechanisms of aluminum alloys under biaxial tensile conditions, essential for optimizing material performance in engineering applications.

High-temperature, low-cycle fatigue behavior of an Al-Mg-Si based heat-resistant aluminum alloy

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

High Temperature Tensile Deformation Behavior of New Heat Resistant Aluminum Alloy

Strain Ratio Effects on Low-Cycle Fatigue Behavior and Deformation Microstructure of 2124-T851 Aluminum Alloy

Cyclic Deformation Behavior of A Heat-Treated Die-Cast Al-Mg-Si-Based Aluminum Alloy

Low cycle fatigue response and fracture mechanism in a novel Al-3.5Si-0.5Mg-0.4Cu casting alloy

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

Significantly enhanced fatigue resistance and mechanisms of hypoeutectic Al-Si composite calibrated using trace in-situ nanocrystals

Study on Microstructure and Mechanical Properties of Al-Mg-Si-Cu Aluminium Alloy with High Ductility

Rotating bending fatigue behavior of high-pressure diecast AlSi10MgMn alloy based on T5 heat treatment parameters

Microstructural Evolutions and Strengthening Mechanism according to the Aging Temperatures of a High Si Cast Aluminum Alloy

Thermo-Mechanical Fatigue Behavior and Resultant Microstructure Evolution in Al-Si 319 and 356 Cast Alloys

Effect of nano-clay addition and heat-treatment on tensile and stress-controlled low-cycle fatigue behaviors of aluminum-silicon alloy: Effect of nano-clay addition and heat-treatment

Hot dwell-fatigue behaviour of additively manufactured AlSi10Mg alloy: Relaxation, cyclic softening and fracture mechanisms

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

High Temperature Low-Cycle Fatigue, Deformation Microstructure and Final Fracture Behavior of a Nickel-Base Superalloy

Stabilizing Al–Mg–Si–Cu alloy by precipitation nano-phase control

Influence of Severe Plastic Deformation and Aging on Low Cycle Fatigue Behavior of Al-Mg-Si Alloys

Investigation of the microstructural behavior of Al–Mg–Si(X)–Mn aluminum alloys based on biaxial hot tensile tests

The strengthening role of micro-sized phases and nano-precipitates in Al–Mg 2 Si–Cu(–Ni) alloys at 25 °C and 350 °C

Effect of ageing and thermal exposure on microstructure and mechanical properties of a HPDC Al–Si–Cu–Mg alloy