Abstract:In this paper, high-silicon Al-42Si alloy was prepared by selective laser melting (SLM) with different process parameters. Microstructures evolution and defects formation were studied and process parameters were optimized. The results shown that the density of SLM-fabricated Al-42Si alloy increases as input energy density increases. The highest and lowest density of SLM-fabricated Al-42Si alloy are obtained, when input energy density is 42.9J/mm3 and 33.8J/mm3 respectively. The microstructures of Al-42Si alloy fabricated by selective laser melting is mainly composed of primary silicon phase and eutectic silicon phase, which is distinct from casting alloy because of diffient grains size and shapes of the primary silicon. With higher energy density, larger size of the primary silicon observed during process due to higher heat released by powder. The size of primary silicon phase particles is in the range of 2.9-9.4μm, and the size of molten pool during SLM process is in the range of 125 ± 10μm-140 ± 10μm in this study. Also the hardness of SLM-fabricated Al-42Si alloy increases as input energy density increases between 40.0J/mm3 and 42.9J/mm3. After heat treatment, the residual stress is eliminated, microstructure stability and homogeneous of SLM-fabricated Al-42Si alloy are improved. The silicon distribution is more uniform and sizes increases about 1∼2μm, and the hardness decreases after heat treatment. The optimal SLM parameters for Al-42Si alloy are laser power of 320W, scanning speed of 1355 mm/s, layer thickness of 50μm and scanning space of 110μm.

Microstructures and mechanical properties of Si and Zr modified Al–Zn–Mg–Cu alloy-A comparison between selective laser melting and spark plasma sintering

Microstructures and tensile properties of a selective laser melted Al–Zn–Mg–Cu (Al7075) alloy by Si and Zr microalloying

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Densification, microstructure and properties of Sc and Zr modified Al-Mn alloy prepared by selective laser melting

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Tensile property and microstructure of Al−4.77Mn−1.37Mg−0.67Sc−0.25Zr alloy under different selective laser melting processing parameters

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Selective laser melting of CuCrZr alloy: processing optimisation, microstructure and mechanical properties

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

The microstructures and mechanical properties of Al-Zn-Mg-Cu-Si-Zr alloy: A comparison between directed energy deposition and laser powder bed fusion

Selective Laser Melting of Gas Atomized Al–3.02Mg–0.2Sc–0.1Zr Alloy Powder: Microstructure and Mechanical Properties

The influence of NH 3 plasma treatment on microstructure and mechanical property of AlSi10Mg alloy fabricated by selective laser melting

Study on microstructure and properties of selective laser melting formed AlSi10Mg alloy

Microstructure and Mechanical Properties of an Er-Modified Al–Mg–Mn–Sc–Zr Alloy Processed by Selective Laser Melting

Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms

Microstructural evolution and mechanical properties of pure Zn fabricated by selective laser melting

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Effect of process parameters on microstructures and properties of Al-42Si alloy fabricated by selective laser melting