Abstract:The addition of Sc and Zr into an Al–Mg–Mn alloy produced by selective laser melting exhibited exceptional properties. Multiple factors eventually lead to the improvement of properties, such as densification behaviors, grain characteristics, texture and the precipitated phases. We firstly investigate evolution of the melt pool characteristics which are varied under different processing parameters and lead to different solidified microstructures, densification behaviors and corresponding mechanical properties. Meanwhile, the characteristics of melt pool can be predicted through the normalized enthalpy of input energy, which presents more credible relationship with the melt pool dimensions. To this end, the relative density is up to 99.88% when the volume energy density and normalized enthalpy are combined used. Recrystallisation inhabitations induced by the added Sc and Zr is supposed after comparing the grain sizes under different conditions. Regrettably, the relationship between melt pool characteristics and the equiaxed/columnar ratio can not be described accurately, which due to the pseudo-equiaxed regions in XZ/YZ sections through regulating the melt track orientations via 67° scanning rotation. There are dispersed Al6Mn and Al3(Sc, Zr) particles exist in as-fabricated samples result in better mechanical properties and the subsequent aging treatment can further improve the comprehensive mechanical properties. Finally, the ultimate tensile strength and ductility is separately about 494.32 ± 4.16 MPa and 15 ± 1.27% after aging for 4 h at 325 °C. In contrast, the processing parameters have little impact on mechanical properties, especially for the yield strength, mainly owing to the homologous precipitate phase and grain sizes when the relative density is similar. The connection involving the whole periods from solidification to the final mechanical properties is discussed that may offer feasible ideas for alloy design and corresponding parameter optimization.

Study on microstructure and properties of selective laser melting formed AlSi10Mg alloy

Achieving Superior Strength and Ductility of AlSi10Mg Alloy Fabricated by Selective Laser Melting with Large Laser Power and High Scanning Speed

Effect of Heat Treatment on Microstructure and Properties of Selective Laser Melting AlSi10Mg Alloy

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Microstructural evolution and strengthening mechanism of high-strength AlSi8.1 Mg1.4 alloy produced by selective laser melting

Effect of construction angles on microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Microstructure and Mechanical Properties of Laser Metal Deposited AlSi10Mg Alloys

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

Effects of Heat Treatment on Microstructure and Mechanical Properties of AlSi10Mg Fabricated by Selective Laser Melting Process

Parameter optimization and microhardness experiment of AlSi10Mg alloy prepared by selective laser melting

Effect of Al3(Sc, Zr) and Mg2Si Precipitates on Microstructure and Tensile Properties of Selective Laser Melted Al-14.1Mg-0.47Si-0.31Sc-0.17Zr Alloy

Effect of laser power on microstructures and properties of Al-4.82Mg-0.75Sc-0.49Mn-0.28Zr alloy fabricated by selective laser melting

Influence of Laser Process on the Porosity-Related Defects, Microstructure and Mechanical Properties for Selective Laser Melted AlSi10Mg Alloy

Achieving high strength in selective laser melting AlSi10Mg alloy by adding microsized pure Cu particles

Effect of microstructural evolution on mechanical properties and fracture modes of AlSi10Mg blocks fabricated by selective laser melting after stress relief annealing

Study on the Forming Process and Properties of AlSi60 Alloy by Selective Laser Melting

The Effect of Silicon Phase Morphology on Microstructure and Properties of AlSi10Mg Alloys Fabricated by Selective Laser Melting

Selective laser melting Al-3.4Mg-0.5Mn-0.8Sc-0.4Zr alloys: From melting pool to the microstructure and mechanical properties

Research on the limitations of laser energy density and microstructure characteristics of selective laser melted AlSi10Mg alloy