Abstract:uThe factor that plays important role in the quality of the final product in selective laser melting (SLM) is the process parameter set used in production. In general, these fabrication parameter sets are obtained experimentally by using the energy density requirements of the material. The experimental investigation is partly a trial and error approach, which is a time and cost-consuming process. On the other hand, keeping the temperature of the melt pool in an allowable range, which is dominated by the applied process parameters sets, and preventing temperature fluctuations impress the stability of the production and therefore the quality of the final product. The paper presents a multiphysics numerical model approach for obtaining parameters in an SLM process by using AlSi10Mg powders as the material medium. The proposed approach provides mathematical relationships between the process parameters and the temperature they form. By investigating the effect of laser power and laser spot diameter on the temperature at different scanning velocities, wider process parameter sets were obtained for AlSi10Mg. In addition, mathematical relationships between laser power-temperature and laser spot diameter-temperature at different scanning velocities, which will be the base material to design a controller to control the melt pool temperature instantly, were developed. By using the parameter sets obtained from the simulations, test samples including samples for microstructure study and tensile test specimens were fabricated to validate the model. The un-melted powders and nonconnected melt pool defects due to insufficient temperature, evaporation defects caused by extreme temperature, and appropriate and homogeneous microstructures as a result of suitable parameters that were predicted through simulations, affecting microstructure and mechanical properties, validated the model. The experimental study was carried out by examining the microstructure and tensile properties of the fabricated test samples.

Effects of remelting on the surface morphology, microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

The effect of a remelting treatment scanning strategy on the surface morphology, defect reduction mechanism, and mechanical properties of a selective laser-melted Al-based alloy

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Effect of laser remelting on printability, microstructure and mechanical performance of Al-Mg-Sc-Zr alloy produced by laser powder bed fusion

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Effect of Overlapping Remelting on Microstructures and Mechanical Properties of Selective Laser‐Melted Ti‐6Al‐4V Alloy

On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Role of laser remelting and heat treatment in mechanical and tribological properties of selective laser melted Ti6Al4V alloy

Effect of Heat Treatment on Microstructure and Properties of Selective Laser Melting AlSi10Mg Alloy

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Study on microstructure and properties of selective laser melting formed AlSi10Mg alloy

Microstructural analysis and mechanical properties of AlSi10Mg alloy components produced via SLM

The Effect of Silicon Phase Morphology on Microstructure and Properties of AlSi10Mg Alloys Fabricated by Selective Laser Melting

On the selective laser melting based additive manufacturing of AlSi10Mg: The process parameter investigation through multiphysics simulation and experimental validation

A review on the simulation of selective laser melting AlSi10Mg

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

Thermal and mechanical properties of an Al-Mg-Sc-Zr high strength alloy fabricated by selective laser melting

Effect of process parameters on microstructures and properties of Al-42Si alloy fabricated by selective laser melting

Processing AlSi10Mg by selective laser melting: parameter optimisation and material characterisation