Abstract:The newly designed alloy compositions for selective laser melting (SLM) have aroused great interest. In this study, zirconium modified Al-Cu-Mg alloys were fabricated by SLM. Results show that crack-free samples with relative density of nearly 100% were obtained by optimizing the processing parameters. With the increase of scanning speed, the relative density decreases due to insufficient energy input. In addition, the microstructure transforms from homogeneous to bio-modal, the reason is the unstable flows caused by the high scanning speed. The small hatching space will provide more energy input and preheat, leading to the coarse surface. Introduction Additive Manufacturing (AM) processes enable to fabricate parts with very complex shape[1]. Selective laser melting (SLM), one of the preferred AM techniques, has recently gained considerable attention due to high manufacturing flexibility, nearnet-shape production and efficient use of raw material[2, 3]. Al-Cu-Mg alloy has become an attractive material due to the low density, high fracture toughness and fatigue strength[4, 5]. Nowadays, processing high strength aluminum alloys by SLM is confronted with great difficulties because of its poor flowability, high reflectivity, high thermal conductivity, large solidification range and hot cracking susceptibility[6]. Therefore, the biggest stumbling block to the application of high strength aluminum in SLM is the hot crack. To expand the scope of aluminum alloys suiting for SLM, new high strength aluminum alloys are urgent to be investigated. Recently, scandium (Sc), zirconium (Zr), titanium (Ti) and vanadium (V) have been proved as the effective microalloying element for aluminum alloys to improve the weldability and mechanical properties[7-9]. Nowadays, the addition of microalloying element has been applied to SLM aluminum alloys to improve their formability. The microstructural evolution, densification, properties and heat treatment of Al-Mg-Sc-Zr fabricated by SLM have been investigated[10-13]. Zhang H et al.[14] have found that the Zr modified Al-Cu-Mg parts with ultrafine grain exhibits better mechanical properties and broader processing window. However, the effect of processing parameters on the Zr modified Al-Cu-Mg alloy has not been studied. 1246 Solid Freeform Fabrication 2018: Proceedings of the 29th Annual International Solid Freeform Fabrication Symposium – An Additive Manufacturing Conference Reviewed Paper

The effect of a remelting treatment scanning strategy on the surface morphology, defect reduction mechanism, and mechanical properties of a selective laser-melted Al-based alloy

Effects of remelting on the surface morphology, microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Influence of Scanning Strategy and Parameter on Microstructural Feature, Residual Stress and Performance of Sc and Zr Modified Al–Mg Alloy Produced by Selective Laser Melting

Microstructure and Anisotropic Mechanical Properties of Selective Laser Melted Ti6Al4V Alloy under Different Scanning Strategies

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Selective laser melting of Al 6061 alloy : Processing , microstructure , and mechanical properties

A Novel Two-Stage Heat Treatment with Medium-Temperature Aging Influence on Microstructure, Al3(Sc, Zr) Nanoprecipitation, and Application Properties, Enhancing Selective Laser Melting of Al–Mg–Sc–Zr Alloy

Selective Laser Melting of A Novel Sc and Zr Modified Al-6.2 Mg Alloy: Processing, Microstructure, and Properties

Influence of Scanning Strategy and Post-Treatment on Cracks and Mechanical Properties of Selective-Laser-Melted K438 Superalloy

Investigating the effect of the scanning speed on the characteristics of Al-Li alloy fabricated by selective laser melting

The effect of processing parameter on zirconium modified Al-Cu-Mg alloys fabricated by selective laser melting

Effect of laser remelting on printability, microstructure and mechanical performance of Al-Mg-Sc-Zr alloy produced by laser powder bed fusion

Effect of Heat Treatments on the Microstructure and Mechanical Properties of Al-Mg-Sc-Zr Alloy Fabricated by Selective Laser Melting

Process Optimization and Mechanical Property Evolution of AlSiMg0.75 by Selective Laser Melting

Effect of Heat Treatment on Microstructure and Properties of Selective Laser Melting AlSi10Mg Alloy

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

Selective laser melting Al-3.4Mg-0.5Mn-0.8Sc-0.4Zr alloys: From melting pool to the microstructure and mechanical properties

Thermal and mechanical properties of an Al-Mg-Sc-Zr high strength alloy fabricated by selective laser melting

Study on the Effect of Remelt Scanning and Heat Treatment Processes on the Structure and Properties of Laser Powder Bed Fusion Formed Al-Mg-Sc-Zr Alloys

Influence Mechanism of Process Parameters on Relative Density, Microstructure, and Mechanical Properties of Low Sc-Content Al-Mg-Sc-Zr Alloy Fabricated by Selective Laser Melting