Abstract:uThe factor that plays important role in the quality of the final product in selective laser melting (SLM) is the process parameter set used in production. In general, these fabrication parameter sets are obtained experimentally by using the energy density requirements of the material. The experimental investigation is partly a trial and error approach, which is a time and cost-consuming process. On the other hand, keeping the temperature of the melt pool in an allowable range, which is dominated by the applied process parameters sets, and preventing temperature fluctuations impress the stability of the production and therefore the quality of the final product. The paper presents a multiphysics numerical model approach for obtaining parameters in an SLM process by using AlSi10Mg powders as the material medium. The proposed approach provides mathematical relationships between the process parameters and the temperature they form. By investigating the effect of laser power and laser spot diameter on the temperature at different scanning velocities, wider process parameter sets were obtained for AlSi10Mg. In addition, mathematical relationships between laser power-temperature and laser spot diameter-temperature at different scanning velocities, which will be the base material to design a controller to control the melt pool temperature instantly, were developed. By using the parameter sets obtained from the simulations, test samples including samples for microstructure study and tensile test specimens were fabricated to validate the model. The un-melted powders and nonconnected melt pool defects due to insufficient temperature, evaporation defects caused by extreme temperature, and appropriate and homogeneous microstructures as a result of suitable parameters that were predicted through simulations, affecting microstructure and mechanical properties, validated the model. The experimental study was carried out by examining the microstructure and tensile properties of the fabricated test samples.

Microstructural analysis and mechanical properties of AlSi10Mg alloy components produced via SLM

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties

Investigation for Macro Mechanical Behavior Explicitly for Thin-Walled Parts of AlSi10Mg Alloy Using Selective Laser Melting Technique

Microstructure, wear and residual stresses of selective laser melting AlSi10Mg solid cylinder

The Effect of Selective Laser Melting Process Parameters on the Microstructure and Mechanical Properties of Al6061 and AlSi10Mg Alloys

Anisotropy of Microstructure and Tensile Properties of AlSi10Mg Formed by Selective Laser Melting

Selective laser melting of Al 6061 alloy : Processing , microstructure , and mechanical properties

Process parameter optimization and mechanical properties for selective laser melting of AlSi10Mg alloy

Microstructure, porosity and mechanical properties of selective laser melted AlSi10Mg

Comparative Study of Performance Comparison of AlSi10Mg Alloy Prepared by Selective Laser Melting and Casting

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Processing AlSi10Mg by selective laser melting: parameter optimisation and material characterisation

Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: Microstructure and mechanical properties in as-built/as-cast and heat-treated conditions

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

Selective Laser Melting of High Strength Al–Cu–Mg Alloys: Processing, Microstructure and Mechanical Properties

Selective Laser Melting Process Optimization and Mechanical Properties Evolution of AlSi10Mg by Determining Temperature of the Build Chamber using Arduino IDE and Coding Algorithm

On the selective laser melting based additive manufacturing of AlSi10Mg: The process parameter investigation through multiphysics simulation and experimental validation

A review on factors influencing mechanical properties of AlSi12 alloy processed by selective laser melting

Additive manufacturing of a high strength Al-5Mg2Si-2Mg alloy: Microstructure and mechanical properties

Effect of Laser Parameters on Microstructure, Metallurgical Defects and Property of AlSi10Mg Printed by Selective Laser Melting