Abstract:The selective laser melting (SLM) technology, a 3D printing method, has been gaining more attraction recently due to its ability to fabricate highly complex and intricate featured medical, aerospace, automotive components. The extensive use of SLM in recent years has been augmented by readily available processing materials and distinct product features such as enhanced surface properties and improved mechanical strength of the printed products. This paper investigated the effects of support structures, building direction and post-processing on mechanical properties, surface roughness and microscopic analysis of parts printed by SLM. Support structures are required during the SLM printing process. It is desired to optimize the support structures, as this increases printing time and material consumption and reduces surface finish. Finite element analysis has been carried out prior to metal printing to optimize the support structure. It was found that the spider-cone line support shows efficient structure for this study. The mechanical properties of the fabricated specimen were studied, and experimental results were validated and compared with conventionally machined specimen. It was observed that the SLM printed parts have 20% increment in tensile strength as compared with conventionally cast specimen. However, the percent of elongation is low for SLM specimen due to large number of pores and un-melted powder presented in the printed part. In this study, the SLM specimens were subjected to heat treatment at the temperature of 550 °C for 2 h in order to achieve increment or optimal mechanical properties. The heat treatment demonstrated a 2-fold increment in elongation, as compared with the SLM as printed specimen. The present study is also aimed at evaluating the surface roughness of SLM printed specimen. It was observed that the surface roughness of SLM specimen ranged between ~ 0.3 and 3 μm. This demonstrated that SLM process is capable of providing the good surface quality component and considered an alternative process to conventional manufacturing process. The morphological studies have been carried out to support the results derived from the evaluation of mechanical properties and surface roughness. The morphological behaviour clearly shows the large pores and un-melted particles in fractured specimen. The results revealed that the support structure, build direction, orientation, surface finish and post-processing are important parameters to build a part using SLM effectively and efficiently.

Effects processing parameters and building orientation on the microstructural and mechanical properties of AlSilOMg parts printed by selective laser melting

Effect of microstructural evolution on mechanical properties and fracture modes of AlSi10Mg blocks fabricated by selective laser melting after stress relief annealing

Effect of building orientations and heat treatments on AlSi10Mg alloy fabricated by selective laser melting: microstructure evolution, mechanical properties, fracture mechanism and corrosion behavior

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Effects of Heat Treatment on Microstructure and Mechanical Properties of AlSi10Mg Fabricated by Selective Laser Melting Process

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Influence of printing parameters on structures, mechanical properties and surface characterization of aluminium alloy manufactured using selective laser melting

Microstructural analysis and mechanical properties of AlSi10Mg alloy components produced via SLM

Thermal and mechanical properties of an Al-Mg-Sc-Zr high strength alloy fabricated by selective laser melting

Microstructure, wear and residual stresses of selective laser melting AlSi10Mg solid cylinder

The effect of a remelting treatment scanning strategy on the surface morphology, defect reduction mechanism, and mechanical properties of a selective laser-melted Al-based alloy

Selective Laser Melting Process Optimization and Mechanical Properties Evolution of AlSi10Mg by Determining Temperature of the Build Chamber using Arduino IDE and Coding Algorithm

On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties

Processing AlSi10Mg by selective laser melting: parameter optimisation and material characterisation

Effect of the Boundary Orientation of Melt Pool on Mechanical Property and Fracture Path in Selective-Laser-Melted AlSi10Mg Alloy

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

The Effect of Silicon Phase Morphology on Microstructure and Properties of AlSi10Mg Alloys Fabricated by Selective Laser Melting

Effect of construction angles on microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Effect of process parameters of selective laser melting on the structure, texture, and mechanical properties of an alloy based on orthorhombic titanium aluminide Ti2AlNb

Influence of Selective Laser Melting Machine Source on the Dynamic Properties of AlSi10Mg Alloy