Abstract:Purpose To fabricate a selective laser melting (SLM)-processed AlSi10Mg part with almost full density and free of any apparent pores, this study aims to investigate the effect of ambient argon pressure and laser scanning speed on the particles splash during the AlSi10Mg powder bed laser melting. Design/methodology/approach Based on the discrete element method (DEM), a 3D model of random distribution of powder particles was established, and the 3D free surface of SLM forming process was dynamically tracked by the volume of fluid, where a Gaussian laser beam acts as the energy source melting the powder bed. Through the numerical simulation and process experimental research, the effect of the applied laser power and scanning speed on the operating laser melting temperature was studied. Findings The process stability has a fundamental role in the porosity formation, which is process-dependent. The effect of the processing conditions on the process stability and the resultant forming defects were clarified. Research limitations/implications The results shows that the pores were the main defects present in the SLM-processed AlSi10Mg sample, which decreases the densification level of the sample. Practical implications The optimal processing parameters (argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm ) applied during laser melting can improve the quality of selective laser melting of AlSi10Mg, Social implications It can provide a technological support for 3D printing. Originality/value Based on the analysis of the pore and balling formation mechanisms, the optimal processing parameters have been obtained, which were argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm. Then, a near-fully dense sample free of any apparent pores on the cross-sectional microstructure was produced by SLM, wherein the relative density of the as-built samples is larger than 97.5%.

Experimental Research on Selective Laser Melting AlSi10Mg Alloys: Process, Densification and Performance

Process parameter optimization and mechanical properties for selective laser melting of AlSi10Mg alloy

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Selective Laser Melting of High Strength Al–Cu–Mg Alloys: Processing, Microstructure and Mechanical Properties

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

Parameter optimization and microhardness experiment of AlSi10Mg alloy prepared by selective laser melting

Achieving Superior Strength and Ductility of AlSi10Mg Alloy Fabricated by Selective Laser Melting with Large Laser Power and High Scanning Speed

Effect of Processing Parameters on Forming Defects During Selective Laser Melting of AlSi10Mg Powder

Processing AlSi10Mg by selective laser melting: parameter optimisation and material characterisation

Effect of Processing Parameters on the Densification of an Additively Manufactured 2024 Al Alloy

Microstructure, porosity and mechanical properties of selective laser melted AlSi10Mg

Effect of process parameters on microstructures and properties of Al-42Si alloy fabricated by selective laser melting

Process Optimization and Mechanical Property Evolution of AlSiMg0.75 by Selective Laser Melting

Influence Mechanism of Process Parameters on Relative Density, Microstructure, and Mechanical Properties of Low Sc-Content Al-Mg-Sc-Zr Alloy Fabricated by Selective Laser Melting

Densification, microstructure and properties of Sc and Zr modified Al-Mn alloy prepared by selective laser melting

Investigation for Macro Mechanical Behavior Explicitly for Thin-Walled Parts of AlSi10Mg Alloy Using Selective Laser Melting Technique

A Study on Sc- and Zr-modified Al–Mg Alloys Processed by Selective Laser Melting

Effect of Selective Laser Melting Process Parameters on the Quality of Al Alloy Parts: Powder Characterization, Density, Surface Roughness, and Dimensional Accuracy

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

Effect of Laser Parameters on Microstructure, Metallurgical Defects and Property of AlSi10Mg Printed by Selective Laser Melting