Abstract:Semi-solid thixoforming processes rely on a material microstructure made of globular solid grains more or less connected to each other, thus developing a solid skeleton deforming into a liquid phase. During processing, the material structure changes with the processing history due to the agglomeration of the particles and the breaking of the grains bonds. This particular evolutive microstructure makes semi-solid materials behave as solids at rest and as liquids during shearing, which causes a decrease of the viscosity and of the resistance to deformation while shearing. Thixoforming of aluminum and magnesium alloys is state of the art and a growing number of serial production lines are in operation all over the world. But there are only few applications of semi-solid processing of higher melting point alloys such as steel. This can partly be attributed to the high forming temperature combined with the intense high temperature corrosion that requires new technical solutions. However the semi-solid forming of steels reveals high potential to reduce material as well as energy consumption compared to conventional process technologies, such as casting and forging. Simulation techniques exhibit a great potential to acquire a good understanding of the semi-solid material process. Therefore, this work deals with the development of an appropriate constitutive model for semi-solid thixoforming of steel. The constitutive law should be able to simulate the complex rheology of semi-solid materials, under both steady-state and transient conditions. For example, the peak of viscosity at start of a fast loading should be reproduced. The use of a nite yield stress is appropriate because a vertical billet does not collapse under its own weight unless the liquid fraction is too high. Furthermore, this choice along with a non-rigid solid formalism allows predicting the residual stresses after cooling down to room temperature. Several one-phase material modeling have been proposed and are compared. Thermomechanical modeling using a thermo-elasto-viscoplastic constitutive law has been developed. The basic idea is to extend the classical isotropic hardening and viscosity laws to the non solid state by considering two non-dimensional internal parameters. The rst internal parameter is the liquid fraction and depends on the temperature only. The second one is a structural parameter that characterizes the degree of structural build up in the microstructure. Those internal parameters can depend on each other. The internal parameters act on the the viscosity law and on the yield surface evolution law. Di erent formulations of viscosity and hardening laws have been proposed and are compared to each other. In all cases, the semi-solid state is treated as a particular case, and the constitutive modeling remains valid over the whole range of temperature, starting from room temperature to above the liquidus. These models are tested and illustrated by mean of several representative numerical applications.

Comparison of Rheological Models to Simulate Die Filling Process of A356 Semisolid Alloy

Numerical Simulation of Cavity-Filling Procedures for Micro-Pin-fin Array Thixoforming with Semi-Solid A356 Aluminium Alloy

On the Size Effects in Micro/meso Semisolid Extrusion–forging of A356 Aluminum Alloy

Comparison of Filling Process of A356 Alloy in Semi-solid Thixo-forming Die Casting with in Conventional Die Casting Based on Numerical Simulation with Flow-3D

Rheological Modeling of 7075 Aluminum Alloy Semi-Solid Slurry and its Application in the Simulation of SEED Rheocasting Process

Rheological Behavior of the A356 Alloy in the Semisolid State at Low Shear Rates

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Rheological characterization of a thixotropic semisolid slurry by means of numerical simulations of squeeze flow experiments

The Influences of the Microstructure Morphology of A356 Alloy on Its Rheological Behavior in the Semi-Solid State

Rheologic Properties of Aluminum Alloy A356 Bille ts Produced by Semisolid Continuous Casting Process

New technique for preparing A356 alloy semisolid slurry and its rheo-diecast microstructure and properties

Rheological Behavior of Semisolid A356 Alloy with Different Morphology of Primary Α Phases

Multiphase modelling of the transient flow for Sn-15Pb and 357.0 alloys in semi-solid die casting process

Predicting the constitutive behavior of semi-solids via a direct finite element simulation: application to AA5182

Semi-solid constitutive modeling for the numerical simulation of thixoforming processes.

Rheological modeling and simulation of semi-solid slurry based on experimental study

Experimental Investigation and Numerical Simulation of the Fluidity of A356 Aluminum Alloy

Study on Macro- and Micromodeling of the Solidification Process of Aluminum Shape Casting

Numerical Simulation of 6061 Aluminum Alloys during the Semi-Solid Backward Extrusion

Semi-Solid Slurries for Rheocasting of Hypoeutectic Al-Si-X Alloys Produced by Self-Stirring in Serpentine Channels

Effect of Fluid Flow on Microstructure Evolution During Rheo Gravity Die Casting of Novel Al–15Mg2Si–4.5Si Composite