Abstract:Aluminum casting alloys have properties which are of great industrial interest, such as low density, good corrosion resistance, high thermal and electrical conductivities, good combination of mechanical properties, good workability in machining processes and mechanical forming. Currently, these alloys are produced in various systems and dozens of compositions. In this investigation, a mutual interaction of thermal parameters, scale of the dendritic microstructure, intermetallic compounds (IMCs), microhardness and tensile properties/fracture characteristics of a casting Al–7wt%Si–3wt%Cu–0.3wt%Fe alloy was analyzed. Solidification experiments were developed using a furnace that promoted horizontal growth under transient heat flow conditions. Then, growth rate (VL), cooling rate (CR), and local solidification time (tSL) were determined from measured temperature profiles. Secondary dendritic spacings (λ2), Si particles, Fe-rich and Al2Cu intermetallic phases were characterized by optical and SEM microscopy, as well as the area mapping and point-wise EDS microanalysis. Hence, the interrelations involving Vickers microhardness (HV), yield strength (σYS), ultimate tensile strength (σUTS) and elongation (E%) with microstructural features were evaluated by mathematical equations. IMCs as well as morphologies of Si were also analyzed in the fracture regions. In addition, the experimental growth law of λ2 = f(tSL) proposed in this study was compared with a predictive theoretical model reported in the literature for multicomponent alloys. It was observed that areas that tend to grow faster (lowest λ2 values) were associated with the highest σUTS and E% values, while HV and σYS properties were not affected by the thermal and microstructural parameters (CR and λ2). In addition, less extensive cleavage planes accompanied by small dimples in were observed in fractured samples with lower λ2 values.

Semisolid forming microstructure of Al-Cu5-Ti-Mn alloy

Effects of Solid–Liquid Mixing on Microstructure of Semi-Solid A356 Aluminum Alloy

Preparation of Al-5.8%Cu Alloy Semi-Solid Slurry by Controlled Melting

Comparison of the semisolid squeeze casting and gravity casting process on the precipitation behavior and mechanical properties of the Al-Si-Cu-Mg alloy

Formation of Spheroidal Microstructure in Semi-solid State of Al-4.8Si-2.8Cu-0.5Mg Aluminium Alloy

Microstructure characteristics and strengthening mechanism of semisolid CuSn10P1 alloys

A new insight into high-strength Ti 62 Nb 12.2 Fe 13.6 Co 6.4 Al 5.8 alloys with bimodal microstructure fabricated by semi-solid sintering

Efficient fabrication of semisolid nondendritic Al alloy slurry with high quality

Compound Fabrication Technology of Semi-Solid Billet of Al-Si Alloy Based on SIMA Method

On the Sc induced solidification-heterogeneous microstructure in selective laser melted Al-5Mn alloys

Multi-scale Modeling of Liquid-Metal Cooling Directional Solidification and Solidification Behavior of Nickel-Based Superalloy Casting

Unsteady-State Horizontal Solidification of an Al–Si–Cu–Fe Alloy: Relationship Between Thermal Parameters and Microstructure with Mechanical Properties/Fracture Feature

Bi-modally grained Ti-based alloys fabricated by semi-solid sintering based on the hypoeutectic transformation

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Microstructural Characterization of the As-Cast and Homogenized Al-Cu-Mg-Ag Alloy

Semi-Solid Slurry Preparation Process, Microstructure and Mechanical Properties of Mg–7Al–1Ca–1Sb Alloy

Microstructure Comparison for AlSn20Cu Antifriction Alloys Prepared by Semi-Continuous Casting, Semi-Solid Die Casting, and Spray Forming

Achieving strength-ductility synergy in Al-4.5 wt%Cu binary alloy through semisolid isothermal treatment coupled with ECAP

Microstructure and high temperature tensile properties of Al–Si–Cu–Mn–Fe alloys prepared by semi-solid thixoforming

Enhanced comprehensive performance via alloying and rheo-diecasting in a semi-solid Al–Si–Fe–Mg–Cu–Sr alloy

Microstructure Evolution and Tensile Properties of In Situ TiB2(p)/Al-Cu Composite Processed by Modified Strain-Induced Melt Activation Method with Equal Channel Angular Pressing Pre-deformation