Abstract:<p>Studies on the rheoforming of high melting point alloys are scarce due to the difficulties in preparing semisolid slurries. This work applied a novel enclosed cooling slope channel (ECSC) to prepare a semisolid slurry and squeeze cast a CuSn10P1 (weight percent) alloy. The microstructure and phase formation of the semisolid slurry, properties of liquid squeeze casting, rheo-squeeze casting with or without isothermal treatment of the semisolid slurry were investigated through X-ray diffraction, scanning electron microscopy, electron probe microanalysis, nanoindentation, and transmission electron microscopy. The results show that the microstructure is transformed from coarse dendrites of as-cast to equiaxed grains of semisolid. The high cooling rate of the ECSC process and the semisolid slurry isothermal treatment suppressed tin diffusion to induce the formation of the metastable phase β′-Cu<sub>13.7</sub>Sn. The average values of the modulus and micro-hardness of the rheo-squeeze part after soaking for 20 s were 121.99 ± 14.03 GPa and 2.01 ± 0.94 GPa, which was lower than that without isothermal and liquid squeeze casting, indicating that it has good deformability. The tensile strength and elongation of the rheo-squeeze part after 20 s of soaking treatment are 417 MPa and 12.6%, which increase by 26.3% and three times, respectively, compared to those without isothermal and liquid squeezing, which is likely attributed to solution strengthening, fine grain strengthening, and microstructure homogenization. In addition, the fracture mechanism was transformed from the brittle fracture of liquid squeeze and rheo-squeeze casting without isothermal treatment to a combination of cleavage fracture and ductile fracture of rheo-squeeze casting with 20 s of soaking treatment.</p>

Preparation of Al-5.8%Cu Alloy Semi-Solid Slurry by Controlled Melting

Influences of Master Alloys and Their Preparation Conditions on Microstructures of Semi-solid A356 Alloy Slurries

Efficient fabrication of semisolid nondendritic Al alloy slurry with high quality

Semisolid forming microstructure of Al-Cu5-Ti-Mn alloy

Preparation of Semi-Solid A356 Al Alloy Slurry by Repeated Heating-Cooling Method with Elliptical-Twisted Tubes

On-line Preparation Technology of Semi-Solid Slurry of A356.2 Alloy

Effects of Solid–Liquid Mixing on Microstructure of Semi-Solid A356 Aluminum Alloy

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Novel Partial Remelting Process and Microstructure Evolution of Semi-Solid 2024 Alloy

Rapid Multiple Slurry-Preparation Technology of Melt Treatment and Reversible Electromagnetic Stirring

Using the Phase Field Method to Investigate Microstructural Evolution of Semi-Solid 357.0 Slurries

Enhanced comprehensive performance via alloying and rheo-diecasting in a semi-solid Al–Si–Fe–Mg–Cu–Sr alloy

Rapid Solidification Structure Refinement Mechanism in Highly Undercooled Cu Based Ternary Alloys

Effect of Minor Addition of Co on Nonequilibrium Solidification of Deeply Undercooled Cu Based Alloys

Self-inoculation Method for Preparation of Semi-solid Slurry

Microstructure Evolution of Al-Si Semi-Solid Slurry by Gas Bubble Stirring Method

Microstructure uniformity control of CuCr alloy prepared in-situ by aluminothermic reduction coupled with permanent magnetic stirring

New technique for preparing A356 alloy semisolid slurry and its rheo-diecast microstructure and properties

Preparation of semi-solid 6061 aluminum alloy slurry by serpentine channel pouring

Semi-Solid Slurry Preparation Process, Microstructure and Mechanical Properties of Mg–7Al–1Ca–1Sb Alloy

Microstructure characteristics and strengthening mechanism of semisolid CuSn10P1 alloys